User manual YAMAHA RX-E600

[. . . ] RX-E600 Receiver Récepteur OWNER'S MANUAL MODE D'EMPLOI IMPORTANT SAFETY INSTRUCTIONS 10 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 11 · Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 12 13 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 14 1 2 3 4 5 Read Instructions ­ All the safety and operating instructions should be read before the product is operated. [. . . ] Then peel the sheet off with the tape. ER W PO PO 3 W ER 3 3 3 2 6 2 6 6 6 9 2 2 5 1 1 5 5 5 8 1 1 4 4 8 4 7 7 8 4 7 Note · Do not scratch the remote control surface when peeling the sheet off. 7 8 9 3 GETTING STARTED Connecting the speakers and antennas Do not connect the AC power cord to the wall outlet until all connections have been completed. Follow the steps as shown below to connect the system using the supplied cords and accessories. Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, "+" to "+" and "­" to "­". Right speaker 3 FM antenna Left speaker 2 AM loop antenna C IN MD OUT DVD FM ANT 75 UNBAL. SYSTEM CONNECTOR D A IN R GND AM ANT L TAPE OUT B E IN + ­ SUBWOOFER OUT SYSTEM CONNECTOR DVD IN AUX R L TUNER 6 MIN. /SPEAKER SPEAKERS 1 1 Connect the Speakers. 10 mm (0. 4") of insulation from each of the speaker wires and insert the bare wire into the terminal. 3 Tighten the knob to secure the wire. 4 3 To wall outlet Connect the FM Antenna. FM ANT 75 UNBAL Red: positive(+) Black: negative(­) 2 1 3 4 Connect the AC power cord to a wall outlet. Notes · Use external FM/AM antennas if you need better reception. · The AM loop antenna should be placed apart from the main unit. Set up the AM loop antenna, then connect it. To connect the subwoofer (optional) You can reinforce the bass frequencies by adding a subwoofer (optional). Connect the SUBWOOFER OUT terminal of the unit to the INPUT terminal of the subwoofer. GND AM ANT 4 GETTING STARTED Connecting the system Connecting the RX-E600 and the DVD-E600 English 1 2 3 Connect to using the Audio pin cable. Connect the SYSTEM CONNECTOR (DVD) of the RX-E600 and the SYSTEM CONNECTOR (RECEIVER) of the DVD-E600 with a system control cable (supplied with the DVD-E600). *The other SYSTEM CONNECTOR of the RX-E600 is for connecting the MDX-E300 or KX-E300. Connect the AC power plug of the DVD-E600 to AC OUTLET of the RX-E600. This configuration allows you to turn all components in the system on and off with one touch, and reduces the standby power consumption of the DVD-E600. <RX-E600> C IN MD OUT To wall outlet DVD FM ANT 75 UNBAL. SYSTEM CONNECTOR D A IN R GND AM ANT L TAPE OUT B E IN + ­ SUBWOOFER OUT SYSTEM CONNECTOR DVD IN AUX R L TUNER 6 MIN. /SPEAKER SPEAKERS 1 Audio pin cable SYSTEM CONNECTOR * RECEIVER 2 System control cable <DVD-E600> 3 To RX-E600 VIDEO OUT Y VIDEO DIGITAL OUT AUDIO OUT L R S VIDEO PR PB COAXIAL OPTICAL E COMPONENT Adding KX-E300 and MDX-E300 to the above system (For details, refer to the owner's manual supplied with the respective component. ) 1 2 3 4 Connect Å and i of RX-E600 to Å and i of KX-E300. Connect Ç and Î of RX-E600 to Ç and Î of MDX-E300. Connect DIGITAL OPTICAL OUT of DVD-E600 to DIGITAL OPTICAL IN of MDX-E300. Take off the covers of the optical fiber cable plug, the DIGITAL OPTICAL OUT jack, and the DIGITAL OPTICAL IN jack before making digital connections. Be sure to replace the terminal's cover when the terminal on the rear panel is not being used, in order to protect from dust. Caution · Do not turn RX-E600 on until all connections between components have been completed. · Do not connect or disconnect the system control cable and/or power cord while the system components are turned on. 5 GETTING STARTED Setting the clock You must set the clock before you use the timer functions. and Canada models, and 24-hour system for Australia model. STANDBY/ON DISPLAY HOUR MIN VOLUME NATURAL SOUND STEREO RECEIVER RX­E600 STANDBY/ON TIMER DISPLAY MEMORY AUTO/MAN'L PRESET/BAND PRESET/TUNING MIN MAX TIMER ADJ BASS PHONES TIMER TREBLE HOUR BALANCE MIN INPUT ­ + ­ + L R TIME ADJ PRESET/BAND 1 2 3 4 Turn on the power by pressing STANDBY/ON on the front panel, or POWER on the remote control. · Press HOUR while holding TIME ADJ and PRESET/BAND to reverse the hour setting. · Press MIN while holding TIME ADJ and PRESET/BAND to reverse the minute setting. To display the clock Press DISPLAY. The current time appears for about 8 seconds, then the normal display returns. [. . . ] The problem is difficult to eliminate, but can be lessened by grounding AM loop antenna. Install an external AM loop antenna. AM broadcast sensitivity is poor. Radio signal is weak or the antenna is not properly connected. Cannot set timer. The internal microcomputer has been frozen by an external electric shock (lightning, excessive static electricity, etc. ) or the power supply with low voltage. Set current time. Unplug the AC power cord from the wall outlet, and then plug in again after about one minute. 17 ADDITIONAL INFORMATION SYMPTOM The remote control does not work. CAUSE The batteries of the remote control are too weak. [. . . ]