User manual YAMAHA RX-397

[. . . ] G RX-397 Stereo Receiver Récepteur stéréo OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING GEBRUIKSAANWIJZING CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, please read this manual carefully. 2 Install this sound system in a well ventilated, cool, dry, clean place ­ away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit. 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. [. . . ] Rotate VOLUME on the front panel (or press VOLUME +/­ on the remote control) to adjust the sound output level. 16 20 VOLUME u PRESET + VOLUME d A/B/C/D/E ­ MUTE 1 Rotate the INPUT selector on the front panel (or press one of the input selector buttons on the remote control) to select the desired input source. INPUT SLEEP POWER 12 26 8 + 4 40 or VOLUME 60 2 ­ Remote control CD/DVD PHONO TUNER STANDBY 0 -dB or Front panel MD TAPE AUX SPEAKERS A B Front panel Remote control 5 Note You cannot select any input source while the TAPE MON indicator lights up in the front panel display. Press STANDBY/ON on the front panel again (or press STANDBY on the remote control) to finish using this unit and set it to the standby mode. STANDBY STANDBY /ON or Front panel Remote control English 15 PLAYING AND RECORDING Adjusting the tonal quality Adjusting the BALANCE control Adjusts the sound output balance of the left and right speakers to compensate for sound imbalance caused by speaker locations or listening room conditions. BALANCE 1 2 3 4 L5 5R 4 0 1 2 3 Adjusting the LOUDNESS control Retains a full tonal range at any volume level, thus compensating for the human ears' loss of sensitivity to high and low-frequency ranges at a low volume level. CAUTION If the PURE DIRECT button is turned on with the LOUDNESS control set at a certain level, the input signals bypass the LOUDNESS control, resulting in a sudden increase in the sound output level. To prevent your ears or the speakers from being undesirably damaged, be sure to press the PURE DIRECT button AFTER lowering the sound output level or AFTER checking that the LOUDNESS control is properly set. Using the PURE DIRECT button Routes input signals from your audio sources so that the input signals bypass the BASS, TREBLE, BALANCE and LOUDNESS controls, thus eliminating any alterations to the audio signals and creating the purest possible sound. PURE DIRECT 1 Rotate the LOUDNESS control on the front panel to the FLAT position. LOUDNESS 1 2 3 4 5 6 7 8 FLAT ­30dB 10 9 Adjusting the BASS and TREBLE controls Adjust the high and low frequency response. TREBLE Increases or decreases the high frequency response. BASS 1 2 3 4 ­5 5+ 4 0 1 2 3 2 3 4 ­5 5+ 4 2 Rotate VOLUME on the front panel (or press VOLUME +/­ on the remote control) to set the sound output level to the loudest listening level that you would listen to. 16 20 VOLUME 12 26 8 + 4 40 or VOLUME 60 TREBLE 1 0 1 2 3 2 ­ Remote control 0 -dB Front panel 3 Rotate the LOUDNESS control until the desired volume is obtained. LOUDNESS 1 2 3 4 5 6 7 8 FLAT ­30dB 10 9 16 PLAYING AND RECORDING Recording a source Notes · The VOLUME, BASS, TREBLE, BALANCE and LOUDNESS controls and the PURE DIRECT buttons have no effect on the source being recorded. · Check the copyright laws in your country to record from records, CDs, radio, etc. Recording copyright-protected material may infringe on copyright laws. 3 Rotate VOLUME on the front panel (or press VOLUME +/­ on the remote control) to adjust the sound output level of the selected source to record from. 16 20 VOLUME 12 26 8 + 4 40 or VOLUME 60 2 ­ 0 -dB Front panel FM/AM l TUNING h PURE DIRECT EDIT MEMORY TUNING MODE TAPE MON Remote control MAN'L/AUTO FM AUTO/MAN'L 16 A/B/C/D/E 1 2 3 4 5 6 7 8 VOLUME 20 12 4 8 4 2 26 INPUT PHONES SPEAKERS A B 3 4 ­5 5+ 4 2 1 BASS 0 1 2 3 3 4 2 TREBLE 1 0 1 2 3 4 ­5 5+ 3 4 2 BALANCE 1 0 1 2 3 4 L5 5R 3 4 2 LOUDNESS 1 FLAT ­30dB 10 9 8 5 6 7 40 Begin recording on the MD recorder, the tape deck or the VCR connected to this unit. STANDBY /ON 60 0 -dB y 2 1 2 3 If the 3-head tape deck is used for recording, you can monitor the sound of recording by pressing TAPE MONITOR. OPERATION Play the selected source to record from. Rotate the INPUT selector on the front panel to select the source you want to record from. INPUT SLEEP POWER CD/DVD PHONO TUNER STANDBY or MD TAPE AUX SPEAKERS A B Front panel Remote control Note You cannot select any input source while the TAPE MON indicator lights up in the front panel display. English 17 PLAYING AND RECORDING Using the sleep timer Use this feature to automatically set this unit to the standby mode after a certain amount of time. The sleep timer is useful when you are going to sleep while this unit is playing or recording a source. The sleep timer also automatically turns off any external components connected to the AC OUTLET(S). 4 Press SLEEP repeatedly so that SLEEP OFF appears in the front panel display. SLEEP 3 1 SLEEP POWER After a few seconds, SLEEP OFF disappears from the front panel display, and the SLEEP indicator turns off. y The sleep timer setting can also be canceled by pressing STANDBY on the remote control (or STANDBY/ON on the front panel) to set this unit to the standby mode. CD/DVD PHONO TUNER STANDBY MD TAPE AUX SPEAKERS A B u PRESET + VOLUME d A/B/C/D/E ­ MUTE Note The sleep timer can only be set with the remote control. 1 Press one of the input selector buttons on the remote control to select an input source. SLEEP POWER CD/DVD PHONO TUNER STANDBY MD TAPE AUX SPEAKERS A B 2 3 Start playback on the selected input source. Press SLEEP repeatedly to set the amount of time before this unit is set to the standby mode. Each time you press SLEEP, the front panel display changes as shown below. SLEEP SLEEP 120 min SLEEP OFF SLEEP 90 min SLEEP 60 min SLEEP 30 min The SLEEP indicator flashes while switching the amount of time for the sleep timer. SLEEP 18 PLAYING AND RECORDING Muting the sound output 1 Press MUTE on the remote control to mute the sound output. The MUTE indicator flashes in the front panel display. MUTE MUTE 2 Press MUTE on the remote control again to resume the sound output. The MUTE indicator disappears from the front panel display. MUTE OPERATION English 19 FM/AM TUNING FM/AM TUNING There are 2 tuning methods; automatic and manual. Select either method according to your preference and the strength of station signals. Automatic tuning Automatic tuning is effective when station signals are strong and there is no interference. 4 Press TUNING l / h once to begin automatic tuning. Press l to tune into a lower frequency. l TUNING h 243 FM/AM l TUNING h PURE DIRECT EDIT MEMORY TUNING MODE TAPE MONITOR MAN'L/AUTO FM AUTO/MAN'L Notes 16 VOLUME A/B/C/D/E 1 2 3 4 5 6 7 8 20 12 26 INPUT SPEAKERS A B 2 3 4 ­5 5+ 4 1 8 BASS 0 1 2 3 3 4 2 TREBLE 1 0 1 2 3 4 ­5 5+ 3 4 2 BALANCE 1 0 1 2 3 4 L5 5R 3 4 2 LOUDNESS 1 FLAT ­30dB 10 9 8 5 6 7 40 4 STANDBY /ON 60 2 0 -dB 1 1 Rotate the INPUT selector (or press TUNER on the remote control) to select TUNER as the input source. INPUT · When you tune into a station, the frequency of the received station is shown in the front panel display. · If the tuning search does not stop at the desired station because the station signals are weak, try using the manual tuning method. TUNER or Front panel Remote control 2 Press FM/AM on the front panel to select the reception band (FM or AM). FM or AM appears in the front panel display. FM/AM 3 Press TUNING MODE on the front panel so that the AUTO indicator lights up in the front panel display. TUNING MODE AUTO/MAN'L AUTO Lights up 20 FM/AM TUNING Manual tuning Manual tuning is effective when station signals are weak. Automatic preset tuning 243 FM/AM l TUNING h PURE DIRECT EDIT MEMORY TUNING MODE TAPE MONITOR MAN'L/AUTO FM AUTO/MAN'L 16 A/B/C/D/E 1 2 3 4 5 6 7 8 VOLUME 20 12 26 INPUT SPEAKERS A B 2 3 4 ­5 5+ 4 1 8 You can use the automatic preset tuning method to automatically store FM stations. This function enables this unit to automatically tune into FM stations with strong signals and store up to 40 (8 stations in each of the 5 groups, A1 to E8) of those received stations in order. You can then easily recall any preset stations by selecting the preset station numbers where they are stored. Notes · Any station data stored under a preset station number is cleared when you store a new station under that preset station number. · If the number of received stations does not reach 40 (E8), automatic preset tuning automatically stops once searching all available stations are tuned into and stored. [. . . ] 65/50 dB or more · Tone Control Characteristics BASS Boost/Cut (50 Hz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB Turnover Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 Hz TREBLE Boost/Cut (20 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB Turnover Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]