User manual YAMAHA RM1X 2

[. . . ] IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. [. . . ] Changes of offsets the values of all occurences of the specified type of control change data with the specified segment. Delete all data from selected track, cancel voice setting, and reinitialize play effects. Actually applies the PLAY FX and GRID GROOVE settings to the sequence data, overwriting the existing sequence data. Separates the note events in a specified track and places the notes corresponding to different drum instruments in separate tracks. page 82 82 84 85 86 87 87 88 88 89 89 89 90 90 91 91 92 92 92 93 93 93 94 94 95 95 95 95 96 96 96 97 97 97 98 98 98 PATTERN MODE 14 Create Continuous Data 15 Thin Out 16 Modify Control Data 17 18 19 20 21 22 23 24 25 26 27 28 29 Time Stretch Copy Phrase Exchange Phrase Mix Phrase Append Phrase Split Phrase Get Phrase Put Phrase Clear Phrase Phrase Name Copy Track Exchange Track Clear Track 30 Normalize Play Effect 31 Divide Drum Track 32 33 34 35 36 Copy Pattern Append Pattern Split Pattern Clear Pattern Style Name 80 RM1x SEQUENCE REMIXER 12. Job Parameter Category Job Select Values UNDO/REDO, NOTE, EVENT, PHRASE, TRACK, PATTERN 00 . . . Jumps to the job currently selected in the job list. To Select a Job 1 Press the SUBMODE [JOB] button. There are several ways to do this, as listed below: CURSOR buttons Display Knobs Use the CURSOR buttons to scroll to the desired job, then press the Select function button (F4, below "Select" on the display). Use the knob below "JOB" on the display to scroll through the job list, then press the Select function button (F4, below "Select" on the display). You can also use the CATEGORY knob to switch between job categories (listed to the left of the jobs). Press the [NO - 1] or [YES + 1] button once briefly to single-step through the menu in the corresponding direction, or hold the button for continuous scrolling. When the desired job has been highlighted, press the Select function button (F4, below "Select" on the display). Use the numeric entry method described on page 26 to enter the number of the desired job. Then press the [EXIT] button. n · Do not switch off the power while a job is executing (while the "Executing. . . " message is on the screen), as this may cause destruction of your recorded data. [NO - 1]/[YES + 1] buttons Numeric Selection 3 Press the F4 function button (Select) to go to the selected job. The job parameters are described in the job descriptions which follow. 5 Press the F4 function button (DO!) to execute the job. RM1x SEQUENCE REMIXER 81 PATTERN MODE 12. Job t Undo/Redo Job 00 Undo/Redo 1 t Note Job 01 Quantize 1 2 3 5 PATTERN MODE 2 4 The Undo job cancels the changes you made in your most recent patch session, recording session, editing session, or job, restoring the data to its previous state. The Redo job, which becomes available only after you execute an Undo, cancels the Undo and restores the changes. The Undo/Redo job is effective on PATTERN mode patch sessions, and on PATTERN mode and SONG mode recording sessions, editing sessions, and jobs (with the exception of the Song Name and Phrase Name jobs). If you run a recording session and then an editing session, for example, the Undo will be available only for the editing session. (But note that if you move to a recording, editing, or job screen and then quit without making any changes, this does not count as a session. ) You can undo and then redo the same change as many times as you like (provided that you don't make any other changes in between). This can be useful when you want to compare two versions of your data. [. . . ] Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 FRANCE Yamaha Musique France, Division Professionnelle BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 ASIA HONG KONG Tom Lee Music Co. , Ltd. 11/F. , Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2737-7688 ITALY Yamaha Musica Italia S. P. A. , Combo Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 SPAIN/PORTUGAL Yamaha-Hazen Electronica Musical, S. A. [. . . ]