User manual YAMAHA PSR-3000-PSR-1500

[. . . ] SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. Battery Notice: This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement. WARNING: Do not place this product in a position where anyone could walk on, trip over, or roll anything over power or connecting cords of any kind. [. . . ] Press the [H] (STOP) button or the panel MULTI PAD [STOP] button or the STYLE CONTROL [START/STOP] button to stop recording when you've finished playing the phrase. 126 PSR-3000/1500 Owner's Manual Multi Pad Creating (Multi Pad Creator) 9 10 Listen back to your newly recorded phrase, by pressing the appropriate MULTI PAD button, [1]­[4]. To re-record the phrase, repeat steps 6­8 above. Turn Repeat of each pad On or Off by using the [1] - [4] buttons. If the Repeat parameter is on for the selected pad, playback of the corresponding pad will continue until the MULTI PAD [STOP] button is pressed. If the Repeat parameter is off for the selected pad, playback will end automatically as soon as the end of the phrase is reached. When you press the Multi Pads of which the Repeat is turned on during Song or Style playback, playback will start and repeat in sync with the beat. Turn Chord Match of each pad On or Off by using the [5] [8] buttons. If the Chord Match parameter is on for the selected pad, the corresponding pad is played back according to the chord specified in the chord section of the keyboard generated by turning [ACMP] on, or specified in the LEFT voice section of the keyboard generated by turning [LEFT] on (when turning the [ACMP] off). 11 12 13 Press the [D] button, then enter a name for each Multi Pad by (page 128). Press the [I] button, then save the Multi Pad data as a Bank containg a set of four Pads to the USER or CARD (SmartMedia) drive (page 64). The Multi Pads Multi Pad Step Recording (EDIT) The explanations here apply to when you call up the EDIT page in step #4 described above. The EDIT page indicates the Event list that lets you record notes with absolutely precise timing. This Step Recording procedure is essentially the same as that for Song Recording (pages 145­155), with the exception of the points listed below: · There is no menu for switching channels, since Multi Pads contain data for only a single channel. · In the Multi Pad Creator, only the channel events and System Exclusive messages can be entered. You can switch between the two types of Event Lists by pressing the [F] button. PSR-3000/1500 Owner's Manual 127 Multi Pad Editing (Multi Pad Creator) Multi Pad Editing (Multi Pad Creator) 1 Press the [MULTI PAD SELECT] button to call up the Multi Pad Bank selection display, then select a Bank to be edited on the USER drive. 2 The Multi Pads Press the [8] button to call up the [MULTI PAD EDIT] display, then select a Pad to be edited by pressing any of the [A], [B], [F], and [G] buttons. The number above the Pad name corresponds to the MULTI PAD [1]­[4] buttons. 3 Edit each of the Multi Pads as desired. · Naming Press the [1] button then change the name of each Multi Pad (page 70). · Copying Press the [3] button, select the Multi Pad to be copied, select the destination location, then execute the Copy operation by pressing the [4] button (page 68). · Deleting Press the [5] button then delete the unnecessary Multi Pad (page 69). 128 PSR-3000/1500 Owner's Manual Registering and Recalling Custom Panel Setups -- Registration Memory The Registration Memory function allows you to save (or "register") virtually all panel settings to a Registration Memory button, and then instantly recall your custom panel settings by pressing a single button. The registered settings for eight Registration Memory buttons should be saved as a single Bank (file). Registering and Saving Custom Panel Setups Registering Custom Panel Setups 1 2 Set up the panel controls (such as Voice, Style, effects, and so on) as desired. Refer to the separate Data List for a list of parameters that can be registered with the Registration Memory function. Only the items selected here will be registered. 2 5 Registering and Recalling Custom Panel Setups 3 4 When recalling registration setups, you can also select the items to be recalled or not, even if you selected all items when registering (page 132). no data registered On (green). . . data registered, but not currently selected On (red). . . . . . data registered, and currently selected Deleting an unneeded panel setup See page 131. Deleting all eight current panel setups To delete all the eight current panel setups, turn the [POWER] button ON while holding the B6 key (right-most B key on the keyboard). 3 4 5 Press the [2]­[7] buttons to select items. To cancel the operation, press the [I] (CANCEL) button. Enter or remove the checkmark in the box of the item to determine whether the item should be registered or not, by pressing the [8] button. Press one of the REGISTRATION MEMORY [1]­[8] buttons to register your settings. [. . . ] 25/F. , United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. Tel: 714-522-9011 FRANCE Yamaha Musique France BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 HONG KONG Tom Lee Music Co. , Ltd. 11/F. , Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2737-7688 ITALY Yamaha Musica Italia S. P. A. Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 INDONESIA PT. [. . . ]