User manual YAMAHA PSR-2100-PSR-1100

[. . . ] OWNER'S MANUAL OWNER'S MANUAL Introduction SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. Battery Notice: This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement. WARNING: Do not place this product in a position where anyone could walk on, trip over , or roll anything over power or connecting cords of any kind. [. . . ] Since the changes don't have to be played in real time, you can easily create complex, tight chord changes -- over which you can record the melody in normal fashion. The operations here apply to step 6 on page 100. Entering Chords and Sections (Chord Step) For example, you can input the following chord progression by the procedure described below. MAIN A BREAK MAIN B C F G F G7 C Enter the chords by using the currently selected chord fingering method in the Auto Accompaniment section of the keyboard. 1 Press the MAIN [A] button to specify the section, and enter the chords as shown at right. MAIN A MAIN C F G C 001:1:000 F 001:3:000 Select this note value and play the chords indicated at right. G 002:1:000 2 Press the [BREAK] button to specify the Break section, and enter the chords as shown at right. MAIN A BREAK BREAK INTRO C F G F G7 F 002:3:000 G7 002:4:000 Select this note value and play the chords indicated at right. 102 PSR-2100/1100 Recording Your Performances and Creating Songs -- Song Creator 3 Press the MAIN [B] button to specify the section and enter the chord indicated at right. MAIN A MAIN BREAK MAIN B C F G F G7 C C 003:1:000 Select this note value and play the chords indicated at right. Play back the newly created chord progression Use the [C] ( ) button to move the cursor to the beginning of the song, and press the SONG [START/STOP] button to hear the newly entered notes. The entered data can be edited from the SONG CREATOR (CHD) display (page 109). Finally, press the [F] (EXPAND) button from the SONG CREATOR (CHD) display in order to convert the input data into song data. To enter a fill-in, press the [AUTO FILL IN] button and press one of the MAIN [A]­ [D] buttons. END Mark An "END" mark is shown in the display, indicating the end of the song data. The actual position of the End mark differs depending on the section that is input at the end of the song. When an Ending section is input, the End mark automatically follows the Ending data. When a section other than Ending is input, the End mark is set two measures after the final section. The End mark can be freely set to any position desired. PSR-2100/1100 103 Recording Your Performances and Creating Songs -- Song Creator Select the Recording Options: Starting, Stopping, Punching In/Out -- Rec Mode From this display you can set up how recording is started and stopped for either Quick Recording or Multi Recording. To call up these settings, select the REC MODE display by using the [BACK][NEXT] button, after performing operation steps 1 - 3 on page 99. These settings determine how recording will start. Normal Overwrite recording starts when you press the SONG [START/STOP] button or when you play the keyboard with Synchro standby set to ON. First Key On Overwrite recording starts as soon as you start playing the keyboard. This setting also preserves the previous lead-in data, letting you record over the original lead-in without erasing it. Punch In At The song plays back normally up to the indicated Punch In measure (set by the [3] buttons), then starts overwrite recording at that Punch In measure. Determines the measure at which Punch In overwrite recording starts (when "PUNCH IN AT" is selected). These settings determine how recording will stop as well as what happens to previously recorded data. Replace All This deletes all data following the point at which recording is stopped. Punch Out This maintains all data following the point at which recording is stopped. Punch Out At Overwrite recording continues until the indicated Punch Out measure (set by the [6] buttons), then stops at that Punch Out measure, after which song playback continues normally. F G H I J Calls up the SONG display, from which you can save the edited data. Determines the Punch Out measure -- the measure at which Punch In overwrite recording stops (when "PUNCH OUT AT" is selected). When this is set to ON, you can use the foot pedal 2 to control the punch-in and punch-out points. (The current function assignment of the foot pedal is cancelled. ) Press and hold down the foot pedal to record. Recording stops when you release the pedal. 1 2 3 4 5 6 7 8 About Punch In/Out This feature is useful primarily for re-recording or replacing a specific section of an already recorded channel. [. . . ] 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 FRANCE Yamaha Musique France, S. A. Division Professionnelle BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 ASIA HONG KONG Tom Lee Music Co. , Ltd. 11/F. , Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2737-7688 ITALY Yamaha Musica Italia S. P. A. Combo Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. [. . . ]