User manual YAMAHA PORTATONE PSR-6300

[. . . ] NOTE: The smaller the AWG number , the larger the current handling capacity. This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by Yamaha. If a cart, etc. , is used, please observe all safety markings and instructions that accompany the accessory product. Battery Notice: This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. [. . . ] (This does not apply to MIDI tracks. ) First, make sure the tracks are set to full width. Click on the leftmost down arrow and select "Wide" from the pop-up menu. Click here r Activate all the outputs buses you intend to use. (Bus 1 is on by default and doesn't have such a button. ) Up to nine buses can be activated. In these instructions, we'll use the simplest routing system--only using Bus 1--so leave all the other buses off. (For instructions on how to use multiple buses and multiple mLAN channels, see the box below. ) u Click the Show Master button (shown below) to display the stereo master output channel strip. i To route signals to 01X monitor input, set "MONITOR 17-18" in mLAN Auto Connector (PC 01X) to "2CH, " then set the master outputs from the DAW to Channels 17 and 18, as shown below. Reference Appendix In this setup, all tracks are set to Bus 1 (the default) and Bus 1 is routed to the mLAN master outputs. · It is possible to monitor without decreasing the number of input channels (faders) by using the monitor input function of 01X (direct monitor). · When you are using WDM and ASIO simultaneously, refer to "Setting in the mLAN Auto Connector" in the separate Installation Guide. If any track is not set to Bus 1, click the [Bus] box at the bottom of the channel strip, and select Bus 1 from the pop-up menu. o On the 01X, press the [MONITOR A/B] button so that the lamp lights. The instructions here apply when the default setting is used. 70 01X Owner's Manual Recording/Playback/Remote Control In the instructions above, all tracks were routed to a single mLAN output pair. Here, we'll see how to assign audio tracks to different buses (and hence, separate mLAN output pairs). 1 From the Devices menu, select "VST Outputs. " 2 Activate all the the output buses you intend to use. Click on the "power" button to activate a desired bus. (Bus 1, the master bus, is on by default and doesn't have such a button. ) Up to nine buses can be activated. 7 Use the MIXER/LAYER buttons on the 01X to select the appropriate mLAN output group. Press the [INST] (9-16; mL1-8) button to select mLAN channels 9 - 16, and press [MIDI] (17-24; mL9-16) button to select mLAN channels 17 - 24. 8 Use the appropriate faders to set the levels. Reference The mLAN outputs from the DAW/computer are now routed to the input channels of the 01X (channels 9 24), and can be processed and mixed along with channels 1 - 8. 3 From the Devices menu, select "Mixer. " 4 Make the desired track/bus assignments. Click the [Bus] box at the bottom of the channel strip of the audio track, and select the desired bus from the pop-up menu. · When inputting stereo signals, use odd/even input channels in stereo pair configuration (for example, 9 and 10). (See page 102. ) 5 Set the 01X to Internal operation by pressing the [INTERNAL] button (the lamp lights). 01X Owner's Manual 71 Appendix Getting Started Basics Section so that the lamp is off. ) This enables monitoring of the individual mLAN outputs from the DAW/computer. (Note that the track is highlighted in Cubase SX, and the corresponding channel [SEL] button on the 01X lights. ) These buttons serve the same function as the up/down keys on your computer keyboard. · Press the [SEL] button of the appropriate track. Use the BANK [</>] (Left/Right) buttons if necessary to select the desired `bank' of eight tracks, then press the appropriate [SEL] button. Next marker 74 01X Owner's Manual Recording/Playback/Remote Control Zoom The Zoom controls are another navigation convenience. No longer do you have to mouse with the zoom sliders or the magnifying glass tool or use the Zoom submenu in the sequencer. You'll soon appreciate how easy it is to navigate through your song and change the views of your song data -- right from the 01X. In the Project window for example, you may want to zoom out vertically and see more tracks at a time. Or you may want to zoom in horizontally and see more detail in a few number of measures. Zooming in and out can also help you in the Sample Editor, letting you examine details in the wave or seeing the `entire picture' as needed. q To use Zoom, simultaneously hold down the [ZOOM] button and press one of the cursor buttons to zoom in and out, vertically or horizontally, as desired. Vertical Zoom out Horizontal Horizontal Zoom in Vertical Working in the Mixer window Mixer control -- using the faders and knobs q Hold down [SHIFT] and press the [MIXER (F2)] button to call up the Mixer window. Before Using · The response of the fader in the display is immediate, but you might hear a delay between a fader move and the resulting change in sound. For details on optimizing your system and minimizing latency, refer to the documentation of your sequencer. e Turn the knob on the channel to adjust the pan setting. Flip · Even though the knob is an intuitive, natural control for adjusting pan, you may want to use the fader instead. This "flips" the assignment of the faders and the knobs -- letting you control pan with the faders and volume with the knobs. The Flip feature works in any parameter page that has both fader and knob controls. 01X Owner's Manual 75 Appendix w Zoom can be used in the main Project view, or in any of the editors. w While the song is playing, move one of the faders. [. . . ] Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 BELGIUM/LUXEMBOURG Yamaha Music Central Europe GmbH, Branch Belgium Rue de Geneve (Genevastraat) 10, 1140 - Brussels, Belgium Tel: 02-726 6032 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 25/F. , United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. [. . . ]