User manual YAMAHA PORTASOUND PSS 31

[. . . ] Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. General power tool safety warnings Read all safety warnings and all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injury. [. . . ] Never use router bits with a diameter exceeding the maximum diameter specified in the technical data section. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid hazard. Take special care when routing where the paint is possibly lead based or when routing some woods which may produce toxic dust: - Do not let children or pregnant women enter the work area. The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a standard test method provided by EN 60745 and may be used for comparing one tool with another. The declared vibration emission value may also be used in a preliminary assessment of exposure. The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used. When assessing vibration exposure to determine safety measures required by 2002/44/EC to protect persons regularly using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time. To reduce the risk of injury, the user must read the instruction manual. Always check that the power supply corresponds to the voltage on the rating plate. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard. On/off switch Lock-off button Handle Variable speed control knob Plunge lock lever Spindle lock button Collet Revolver depth stop Depth stop bar Chip deflector Dust extraction adaptor Fit the distance piece (14) to the base of the router using the screws provided. The template guide can be used to make a cutout shape from a template, for instance a letter. secure the template over the workpiece with double-sided tape or `G' clamps. The router bit must extend below the flange of the template guide, to cut the workpiece in the shape of the template. The distance piece can be used for trimming wooden or laminate vertical projections. After turning the revolver depth stop to the desired setting, you can fine-adjust the depth stop to be used. If you want to make several cuts with a different depth of cut, adjust each of the depth stops. Turn the depth stop screw (35) up or down as required using a screwdriver. The copy follower helps to maintain an equal cutting distance along the edge of irregularly shaped workpieces. place the router on the workpiece at the desired distance from the edge to be copied. Adjust the bars of the edge guide until the wheel is in contact with the workpiece. When it is not possible to use the edge guide, for example when routing grooves in the back panel of a bookcase to support shelves, proceed as follows: Select a piece of wood with a straight edge to use as a batten. [. . . ] 1 If a Black & Decker product becomes defective due to faulty materials, workmanship or lack of conformity, within 24 months from the date of purchase, Black & Decker guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to ensure minimum inconvenience to the customer unless: The product has been used for trade, professional or hire purposes; The product has been subjected to misuse or neglect; The product has sustained damage through foreign objects, substances or accidents; Repairs have been attempted by persons other than authorised repair agents or Black & Decker service staff. To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www. [. . . ]