User manual YAMAHA PM5DV2

[. . . ] PM5DV2/DSP5D Editor Owner's Manual Owner's Manual Special Notices · The software and this owner's manual are the exclusive copyrights of Yamaha Corporation. · Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. · Copying of the commercially available music sequence data and/or digital audio files is strictly prohibited except for your personal use. · Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software. [. . . ] This is linked with the MIX encoders on the PM5D panel (if the [MIX MASTER] key is on). A level meter is shown beside the fader. 6 H CUE This button cue-monitors the signal of the MIX channel. This is linked with the MIX [CUE] keys in the MIX section of the PM5D panel. If SOLO is active, this will function as SOLO. 7 8 34 PM5DV2/DSP5D Editor Owner's Manual MIX to MATRIX 2 1 3 4 5 A MATRIX send level This adjusts the send level of the signal sent from the MIX channel to the MATRIX buses. B Pair This indicates the pairing status of adjacent odd-numbered/even-numbered MATRIX channels. You can click the heart symbol to enable/disable pairing. C ON (MATRIX send on/off) This is an on/off switch for the signal sent from the MIX channel to the MATRIX bus. D POINT (Send point) Selects the point from which the signal is sent from the MIX channel to the MATRIX bus. You can choose PRE FADER (immediately before the fader), POST FADER (immediately after the fader), or POST ON (immediately after the MIX [ON] key). E CH to MIX POST POINT Here you can select either POST ON or POST TO ST as the Post position that will be sent from all input channels to the currently selected MIX bus. 35 PM5DV2/DSP5D Editor Owner's Manual If a MATRIX channel is selected CHANNEL SELECT (Channel selection) Except for the fact that the operations apply to a MATRIX channel, and that INPUT PATCH is replaced by OUTPUT PATCH, this is the same as for the channel select area of input channels ( p. 22). COMPRESSOR Except for the fact that the COMP LINK GROUP is A­H, and that the types of signal that can be selected for keyin are different, this is the same as for the compressor of an input channel ( p. 25). INSERT Except for the fact that the insert points that can be selected are different, this is the same as for the insert settings of an input channel ( p. 26). EQUALIZER Except for the fact that there is no LOWER/UPPER button, and that the EQ LINK groups are G/H, this is the same as for the equalizer of a MIX channel ( p. 32). DELAY This is the same as for the delay settings of an input channel ( p. 28). DCA GROUP / MUTE GROUP / SAFE These are the same as the DCA Group / Mute Group / Safe settings of a MIX channel ( p. 33). 36 PM5DV2/DSP5D Editor Owner's Manual Pan / Fader A BALANCE 1 2 This adjusts the left/right output balance of paired channels. This is not shown if pairing is not specified. B ON This switches the MATRIX channel on/off. This is linked with the MATRIX [ON] keys in the MATRIX section of the PM5D panel. C Fader 3 This adjusts the output level of the MATRIX channel. This is linked with the MATRIX encoders in the MATRIX section of the PM5D panel. A level meter is shown beside the fader. D CUE This button cue-monitors the signal of the MATRIX channel. This is linked with the MATRIX [CUE] keys in the MATRIX section of the PM5D panel. If SOLO is active, this will function as SOLO. 4 If a STEREO A/B channel is selected CHANNEL SELECT (Channel selection) Except for the fact that your editing applies to a STEREO A/B channel, this is the same as the channel selection for an input channel ( p. 22). 37 PM5DV2/DSP5D Editor Owner's Manual COMPRESSOR Except for the fact that the COMP LINK GROUP is A­H, and that the types of signal that can be selected for keyin are different, this is the same as for the compressor of an input channel ( p. 25). INSERT Except for the fact that the insert points that can be selected are different, this is the same as for the insert settings of an input channel ( p. 26). EQUALIZER This is the same as the equalizer settings of a MIX channel ( p. 32). DELAY This is the same as for the delay settings of an input channel ( p. 28). DCA GROUP / MUTE GROUP / SAFE These are the same as the DCA Group / Mute Group / Safe settings of a MIX channel ( p. 33). Pan / Fader A BALANCE Adjusts the left/right output balance of the STEREO A/B channel. 1 2 3 B ON This switches the STEREO A/B channel on/off. This is linked with the STEREO [ON] key in the STEREO A/B channel strip of the PM5D panel. C MONO (ST B channel only) Switches the ST B channel between stereo/mono. 4 D Fader Adjusts the output level of the STEREO A/B channel. This is linked with the STEREO fader in the STEREO A/B channel strip of the PM5D panel. A level meter is shown beside the fader. E CUE This button cue-monitors the signal of the STEREO A/B channel. This is linked with the STEREO [CUE] key in the STEREO A/B channel strip of the PM5D panel. If SOLO is active, this will function as SOLO. 5 38 PM5DV2/DSP5D Editor Owner's Manual STEREO to MATRIX 2 1 3 4 A MATRIX send level Here you can adjust the send levels of the signals sent from the STEREO A/B channels to the MATRIX bus. B Pair This indicates the pairing status of adjacent odd-numbered/even-numbered MATRIX channels. You can click the heart symbol to enable/disable pairing. C ON (MATRIX send on/off) This is an on/off switch for the signal sent from the STEREO A/B channel to the MATRIX bus. D POINT (Send point) Selects the point from which the signal is sent from the STEREO A/B channel to the MATRIX bus. You can choose PRE FADER (immediately before the fader), POST FADER (immediately after the fader), or POST ON (immediately after the STEREO [ON] key). 39 PM5DV2/DSP5D Editor Owner's Manual Patch Editor window Here you can assign the input/output port for each channel, its direct output, and its insert-in/out. This window is divided into INPUT PATCH, OUTPUT PATCH, INPUT INSERT PATCH, OUTPUT INSERT PATCH, DIRECT OUT PATCH, and PATCH LIST pages. To switch pages, click the tabs shown in the upper part of the window. INPUT PATCH page Here you can select the input port that is assigned to the input of each input channel. Except for the fact that you can resize the window, the basic operation is the same as in the PM5D's INPUT PATCH screen. NOTE · VIRTUAL SOUNDCHECK is a display-only function. [. . . ] These buttons correspond to the following output channels. MIX 1­24 MATRIX 1­8 STEREO A/B SET ALL CLEAR ALL HINT MIX channels 1­24 MATRIX channels 1­8 STEREO A/B channels Activates solo safe for all output channels Defeats solo safe for all output channels Solo safe settings and cue on/off settings are linked for two paired channels. Solo safe operations can be performed independently of scene memories. I Level meter This is a peak level meter that indicates the level of the signal being output from the CUE OUT jacks. As the point at which the level is detected, you can choose either immediately before the delay provided on the MONITOR/ CUE bus output (when the PRE DELAY button is on), or immediately after it (when the POST DELAY button is on). J MONITOR/CUE DELAY Here you can make settings for the delay function that is provided on the MONITOR/CUE output. Use the knob to specify the delay time (0­1000 msec), and use the DELAY button to turn the delay on/off. [. . . ]