User manual YAMAHA P2700

[. . . ] * Make sure to read the Assembly Manual of the Rack System and the Owner's Manual of the Pad. If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. If this symbol is ignored and the equipment is used improperly, there is a danger or injury to persons handling the equipment, and material damage could occur. 3 1. Mount the pads and the drum trigger module on the rack system. As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat controller. Mounting the hi-hat holder Remove the drum trigger module clamp a from the left of the rack, together with the left leg b. WARNING 2. Assemble the holder clamp for the hi-hat holder ensuring that it is oriented as CAUTION shown in the figure, and then reassemble the left leg b and the drum trigger module clamp a. · Do not let small children assemble or set up this product by themselves, or they may be injured. · Be careful with the edges of the Cymbal Holders and the Tom Holders. [. . . ] · If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning. · When setting up the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall. The rack may overturn or be damaged, resulting in injury. · Watch your fingers when adjusting clamps. · Do not put your hands or feet under the foot pedal or foot switch. Hi-hat holder Holder clamp Drum trigger module clamp a Drum trigger module clamp a NOTICE · Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Applying excessive force to the cable may result in damage to the cable, such as the wires being severed, etc. Alternatively, you can place the packages' cardboard boxes on the floor under the kick pad to protect it from damage. Connect the pads to the drum trigger module. As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module. Clamp bolt D Clamp bolt E Clamp bolt A Clamp bolt C Clamp bolt A Clamp bolt C Clamp bolt D Insert the 9-channel snake cable's straight plugs into the drum trigger module's trigger input jacks ([q SNARE] to [i KICK/o] and [HI-HAT CONTROL]). · If you are using the standard setup, the stickers on each of the snake cable's plugs will indicate the name of the corresponding pad. 2. Plug the 9-channel snake cable's L-shaped plugs into the correct pads. [Locations of pad jacks] [Drum trigger module's rear panel] Mounting the drum trigger module, cymbal pads, and hi-hat pad Cymbal pad: PCY100 Hi-hat pad: PCY100 Drum trigger module Cymbal pad: PCY135 1 2 3 4 Mounting the cymbal pads 1. 5. With the stopper making full contact with the bottom surface of the bolt cover, tighten the stopper's key bolt using a tuning key. [Cymbal pad] [Hi-hat pad] Using a tuning key, loosen the stopper's key bolt. 5 6 7 8 9 DTX500 jack names 1: qSNARE 2: wTOM1/!0 3: eTOM2/!1 4: rTOM3/!2 5: tRIDE 6: yCRASH 7: uHI-HAT 8: iKICK/o 9: HI-HAT CONTROL Stopper Key bolt Straight plug names (as shown on stickers) Bolt cover Tuning key Full contact Stopper Bolt cover [9-channel snake cable] Straight plugs 2. Remove the wing nut, the two felt pads, and the bolt cover from the cymbal holder. Wing nut Felt pads Cymbal holder Full contact SNARE TOM1 TOM2 TOM3 RIDE CRASH HI HAT KICK HH CON 3. In the case of snare and tom pads, wrap the cables around the cable clips to prevent them from being pulled out. L-shaped plugs HH CON HI HAT CRASH KICK SNARE TOM1 TOM2 TOM3 RIDE 6. Place one of the felt pads removed in Step 2 on the cymbal holder. NOTICE Mounting the drum trigger module Bolt cover 7. 1. Attach the module stand (provided) to the underside of the drum trigger module using the module stand fastening screws. Cymbal holder Mount the pad unit on the cymbal stand. Lower the pad unit into place with the cymbal holder's shaft passing through the central hole of the cup section. When mounted, the stopper's pin should rest inside the pad unit's smaller hole. * If you were to play a cymbal pad without the stopper's pin positioned inside the smaller hole, the pad could rotate, causing the cable to be pulled out. It is very important, therefore, to ensure that the stopper is secured as described in Step 5 above. Excessive bending can damage the pad cables. [. . . ] It is very important, therefore, to ensure that the stopper is secured as described in Step 5 above. Excessive bending can damage the pad cables. Ensure, therefore, that these cables are not bent at an extreme angle when wrapped around the clips. 6 1. Connect the drum trigger module to a power supply. Module stand fastening screws Module stand Drum trigger module (back side) 3. Place the stopper on the cymbal holder. * If the key bolt was not sufficiently loosened in Step 1 above, it may not be possible to pass the stopper over the cymbal holder's shaft. In such a case, loosen the key bolt as much as possible without removing it. 8. [. . . ]