User manual YAMAHA NCS500-CT OPERATION MANUAL

[. . . ] NUAGE MASTER Ncs500-CT CONTROL SURFACE Operation Manual Using this manual This operation manual supports keyword searching and linking as follows. Keyword searching Searching for keywords is performed using your pdf viewer’s search function. If you are viewing this manual using Adobe Reader, type the term you wish to find into the Find toolbar and then press your computer’s [Enter] key. Jumping between pages If using Adobe Reader, you can jump forwards and backwards to various pages in this manual. This provides a convenient way to return to your original page after clicking a page link. EN Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 How to Read the Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description of the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Top Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Inputs the Trim Tail position. 6 [SET] Sets the [Input keys] mode to the Set mode. In the Set mode, you can set the Marker to the current Project Cursor position, and set the Cycle Marker to the current Left/Right Locator with the [Input keys]. When you press [SET], the pop-up window for setting the Marker or Cycle Marker is shown on the [Multi function display]. Fade In function Fade Out function Trim Head function Trim Tail function Touch the desired number (field) on the pop-up window to select it for editing. NUAGE MASTER Operation Manual 20 Description of the Device When the pop-up window is shown, the [Input keys] have the following functions. [Input keys] [0] – [9] []/[] [BACK SPACE] [CLEAR] [SET] USER ASSIGNABLE Section Function For inputting numbers to the input position. Determines the input then closes the pop-up window. [PREV -] [NEXT +] [CYCLE . ] Overview This section is used to execute assigned functions. For details on assigning functions, see “User Assignable Settings” (page 44) in NUAGE FADER Hardware Setup. [ESC] Controls and Functions 1 [ENTER] You can set the locator position by [SET] and [LEFT]/ [RIGHT] in the TRANSPORT section. For details, refer to the description of [LEFT] (page 10) in the TRANSPORT section. 2 7 [Input keys] Inputs the parameter. For details, refer to the description of the buttons for changing the mode, such as [LOCATE], [MARKER], etc. 1 [Display access] Calls up the “USER ASSIGNABLE Page” (page 38) in the [Multi function display]. When the USER ASSIGNABLE Page is shown, you can toggle among the banks of the USER ASSIGNABLE Page. 2 [U1] – [U12] Executes the assigned function. The button lights while held down. Lamp Dim Off Description A function can be used. A function cannot be used. NUAGE MASTER Operation Manual 21 Description of the Device AUTOMATION Section 9 [TRIM] Turns Trim on (lit) and off (dim). MULTI FUNCTION DISPLAY Section Overview This section is for operating Automation. The function assignments of the buttons can be changed to other Automation functions as desired. For details on changing the function assignments, see “Automation window” (page 45) in NUAGE MASTER Setup. Controls and Functions 2 1 3 4 5 Overview This section is for displaying and editing the section and channel parameters. The [Multi function display] is a touch screen for displaying the page for editing the section and channel parameters. You can select and edit certain parameters on the page by touching it. NOTICE 6 7 8 9 1 [Display access] Never use a sharp or pointed object such as your fingernail to operate the touch screen. Doing so may scratch the screen and render the touch screen inoperable Calls up the “AUTOMATION Page” (page 37) in the [Multi function display]. 2 To open the page displayed on the [Multi function display], press [Display access] at the upper left of the section or the right side of the [Multi function display]. [FILL PUNCH] [Display access] at upper left of section Turns Fill To Punch on (lit) and off (dim). 3 [FILL TO START] Turns Fill To Start on (lit) and off (dim). 4 [FILL TO END] Turns Fill To End on (lit) and off (dim). 5 [FILL LOOP] Turns Fill Loop on (lit) and off (dim). 6 [TOUCH] Selects the Touch mode. 7 [LATCH] Selects the Auto-Latch mode. 8 [X-OVER] Selects the Cross-Over mode. NUAGE MASTER Operation Manual 22 Description of the Device [Display access] at right side of the [Multi function display] The following chart indicates the relation between the “Label Pane” and the controllable parameters of the [Multi function knob]. Lit by touching knob Knob parameter value Functions on button A/B Knob Button A/B Depending on the page shown on the [Multi function display], the [Multi function knob] has the following functions. Operation Function • Highlights the parameter. • Opens and closes the folder. The [Multi function knobs] are touch-sensitive knobs for adjusting various parameters. Touching Turning Pressing The [Multi function knob] has four separate control operations: touching (which brightens the corresponding parameter indication), turning, pressing, and simultaneously holding down and turning. The [Multi function A and B buttons] are directly below each [Multi function knob]. These buttons are for turning functions on and off or for selecting the controllable parameters of the [Multi function knobs]. The controllable parameters of the [Multi function knobs] change depending on the page shown on the [Multi function display]. The parameter information of the [Multi function knobs] appears on the Label Pane area at the bottom of the page shown on the [Multi function display]. Adjusts the parameter finely (fine mode). Simultaneously holding down and turning When you operate the [Multi function knob] while holding down the appropriate button(s) in the “MODIFIER Section” (page 15), the function changes as follows. Operation Simultaneously holding down [SHIFT] and turning knob Simultaneously holding down [CTRL] and pressing knob Function Adjusts the parameter finely (fine mode). Resets the parameter to the default value. For details on the various pages of the [Multi function display], refer to “Pages Shown on the Multi Function Display” (page 28) in the description of the software programs. NUAGE MASTER Operation Manual 23 Description of the Device Controls and Functions 1 DAW SELECT Section 4 5 6 7 8 9 2 3 Overview This section is for selecting the target DAW software for operation. [. . . ] While a dialog box is open, pressing it performs the same action as clicking the OK button. Its indicator lights up when the last operation can be undone, and it flashes when the last operation can be redone. A redo is performed by pressing the button with the [SHIFT] and [ALT] buttons held down. This button is used to save the current session (same as Save command in the File menu). [. . . ]