User manual YAMAHA MY16-EX

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual YAMAHA MY16-EX. We hope that this YAMAHA MY16-EX user guide will be useful to you.


YAMAHA MY16-EX : Download the complete user guide (559 Ko)

You may also download the following manuals related to this product:

   YAMAHA MY16-EX (594 ko)
   YAMAHA MY16-EX (598 ko)
   YAMAHA MY16-EX (599 ko)
   YAMAHA MY16-EX (619 ko)
   YAMAHA MY16-EX (593 ko)
   YAMAHA MY16-EX (804 ko)
   YAMAHA MY16-EX (1 ko)
   YAMAHA MY16-EX 戵־ (652 ko)
   YAMAHA MY16-EX ANNEXE 1 (588 ko)

Manual abstract: user guide YAMAHA MY16-EX

Detailed instructions for use are in the User's Guide.

[. . . ] Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. [. . . ] The MY16-EX is a 16-channel digital input/output card that enables you to extend the number of channels of compatible cards, such as Yamaha MY16-ES64. Up to three MY16-EX cards can be daisy-chained. ENGLISH About the host devices in which the MY16-EX can be installed Before installing the card in a host device, please refer to the Yamaha Pro Audio web site for the latest information on the compatible host devices in which the card can be installed. Yamaha Pro Audio web site: http://www. yamahaproaudio. com · Ethernet is a trademark of Xerox Corporation. Installation information Please refer to the owner's manual supplied with the host device for installation information. As well as securing the card in place, the fixing screws at the left and right of the card function as electrical grounds. Be sure to screw them in tightly. Accessories Owner's Manual Ferrite core x 2 Part Names and Functions Panel 1 2 A [NEXT MY16-EX IN][NEXT MY16-EX OUT] Connectors These RJ-45 connectors can be connected via an Ethernet cable (CAT5e or higher category) to other MY16-EX cards for transmission and reception of the audio and word clock signals. Daisy-chain the cards in the following order: [NEXT MY16-EX OUT] connector [MASTER SIDE IN] connector on the next card in the daisy chain; [NEXT MY16-EX IN] connector [MASTER SIDE OUT] connector on the next card in the daisy chain. About the cable · Use an Ethernet CAT5e or higher category straight cable in which all eight (8) pins are connected. · Use an STP (Shielded Twisted Pair) cable to prevent electromagnetic interference. Be sure to attach the included ferrite cores to a location close to the plug of each cable that is connected to the [NEXT MY16EX OUT] / [MASTER SIDE OUT] connectors. · Cables up to 3 meters in length can be used. B [MASTER SIDE IN][MASTER SIDE OUT] Connectors These RJ-45 connectors can be connected via an Ethernet cable (CAT5e or higher category) to the [NEXT MY16-EX IN] or [NEXT MY16-EX OUT] connector of the master card, such as a Yamaha MY16-ES64 or other MY16-EX cards, for transmission and reception of the audio and word clock signals. 4 MY16-EX Owner's Manual Part Names and Functions Switches ENGLISH SW1 3 2 1 SW2 48K 96K Emu. SW3 Nat. 4 SW105 OFF SW104 Set these switches as appropriate for your situation and for the device in which the card is installed. A Daisy-chain connection ID (SW1) Mode No. 1 No. 2 No. 3 Position 1 2 3 Assign an ID number to each card in the daisy-chain in sequence, starting with the card closest to the master card (such as the MY16-ES64). B Sampling Frequency (SW2) Mode 44. 1/48 kHz 88. 2/96 kHz Position 48K 96K NOTE: This card supports only Double Speed mode when running at 88. 2/96kHz. (Double Channel mode is not supported. ) C Card ID (SW3) Mode Emulation Native Position Emu. If you set this switch to the [Emu. ] position and switch 2 (SW2) to the [48K] position, the host device will recognize the card as a Yamaha MY16-AT digital I/O card. If you set this switch to the [Emu. ] position and switch 2 (SW2) to the [96K] position, the host device will recognize the card as a Yamaha MY8-AE96 digital I/O card. If you install the card in a host device whose firmware supports the MY16-EX, setting this switch to the [Nat. ] position enables you to make best use of the MY16-EX function. OFF 1 2 3 D SW104/SW105 Leave these switches permanently set to the [OFF] position during use. Otherwise, the card will not operate properly. Word Clock Master settings on the host device If the MY16-EX and the master card (MY16-ES64 etc. ) are installed in the same device, do not select the MY16-EX as the clock master. If the MY16-EX and the master card (MY16-ES64, etc. ) are installed in a different device, you can select the MY16-EX as the clock master. [. . . ] #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374 ARGENTINA Yamaha Music Latin America, S. A. Sucursal de Argentina Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina Tel: 1-4371-7021 SWEDEN Yamaha Scandinavia AB J. Wettergrens Gata 1 Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 TAIWAN Yamaha KHS Music Co. , Ltd. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE YAMAHA MY16-EX




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual YAMAHA MY16-EX will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.