User manual YAMAHA MT-03

[. . . ] E N G L I S H EAU26942 DECLARATION of CONFORMITY We Company: MORIC CO. , LTD. Address: 1450-6 Mori Mori-Machi Shuchi-gun Shizuoka 437-0292 Japan Hereby declare that the product: Kind of equipment: IMMOBILIZER Type-designation: 5SL-00 is in compliance with following norm(s) or documents: R&TTE Directive(1999/5/EC) EN300 330-2 v1. 1. 1(2001-6), EN60950(2000) Two or Three-Wheel Motor Vehicles Directive(97/24/EC: Chapter 8, EMC) Place of issue: Shizuoka, Japan Date of issue: 1 Aug. representative name and signature MORIC CO. , LTD. 1450-6 Mori-machi Shuchi-gun Shizuoka 437-0292 JAPAN Telephone +81-538-85-0757 Facsimile +81-538-85-0456 URL:http://www. moric-jp. com INTRODUCTION EAU10100 Welcome to the Yamaha world of motorcycling!As the owner of the MT-03, you are benefiting from Yamaha's vast experience and newest technology regarding the design and manufacture of high-quality products, which have earned Yamaha a reputation for dependability. [. . . ] ODOMETER READING (x 1, 000 km) 1 10 20 30 40 ANNUAL CHECK 28 Air induction system Muffler and exhaust pipe Lights, signals and switches 1 2 29 30 3 4 EAU18670 5 6 7 8 9 10 NOTE: G The air filter needs more frequent service if you are riding in unusually wet or dusty areas. G Hydraulic brake service G Regularly check and, if necessary, correct the brake fluid level. G Every two years replace the internal components of the brake master cylinders and calipers, and change the brake fluid. G Replace the brake hoses every four years and if cracked or damaged. 6-5 PERIODIC MAINTENANCE AND MINOR REPAIR EAU18771 EAUB1290 EAU19602 Removing and installing panels 1 2 3 4 5 6 7 8 9 10 The panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a panel needs to be removed and installed. Panels A and B Checking the spark plug The spark plug is an important engine component, which is easy to check. Since heat and deposits will cause any spark plug to slowly erode, the spark plug should be removed and checked in accordance with the periodic maintenance and lubrication chart. In addition, the condition of the spark plug can reveal the condition of the engine. Unhook the panel from the hook by sliding the panel upward to release it. Insert the panel on the hook, and slide the panel downward to the original position. Remove the spark plug cap. 6-6 PERIODIC MAINTENANCE AND MINOR REPAIR 2. Remove the spark plug as shown, with the spark plug wrench included in the owner's tool kit. Check that the porcelain insulator around the center electrode of the spark plug is a medium-to-light tan (the ideal color when the vehicle is ridden normally). NOTE: If the spark plug shows a distinctly different color, the engine could be defective. Check the spark plug for electrode erosion and excessive carbon or other deposits, and replace it if necessary. Specified spark plug: CR7E (NGK) To install the spark plug 1. Measure the spark plug gap with a wire thickness gauge and, if necessary, adjust the gap to specification. 2. Clean the surface of the spark plug gasket and its mating surface, and then wipe off any grime from the spark plug threads. Install the spark plug with the spark plug wrench, and then tighten it to the specified torque. Tightening torque: Spark plug: 12. 5 Nm (1. 25 m·kgf, 9. 0 ft·lbf) 1 2 3 4 5 6 7 8 1 NOTE: If a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/41/2 turn past finger tight. However, the spark plug should be tightened to the specified torque as soon as possible. Spark plug gap Spark plug gap: 0. 7-0. 8 mm (0. 028-0. 032 in) 9 10 6-7 PERIODIC MAINTENANCE AND MINOR REPAIR EAUB1350 Engine oil and oil filter element 1 2 3 4 5 6 7 8 9 10 The engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter element replaced at the intervals specified in the periodic maintenance and lubrication chart. To check the engine oil level 1. Place the vehicle on a level surface and hold it in an upright position. NOTE: Make sure that the vehicle is positioned straight up when checking the oil level. [. . . ] Let the motorcycle dry completely before storing or covering it. 1 2 3 4 5 6 7 8 9 10 7-2 MOTORCYCLE CARE AND STORAGE EWA10930 WARNING 0 G 1 2 3 4 5 6 7 8 9 G G G Make sure that there is no oil or wax on the brakes or tires. If necessary, clean the brake discs and brake linings with a regular brake disc cleaner or acetone, and wash the tires with warm water and a mild detergent. Before operating the motorcycle test its braking performance and cornering behavior. ECA10800 NOTE: Consult a Yamaha dealer for advice on what products to use. EAUM1900 Storage Short-term Always store your motorcycle in a cool, dry place and, if necessary, protect it against dust with a porous cover. ECA10810 CAUTION: G CAUTION: G 10 Apply spray oil and wax sparingly and make sure to wipe off any excess Never apply oil or wax to any rubber and plastic parts, but treat them with a suitable care product. Avoid using abrasive polishing compounds as they will wear away the paint. G Storing the motorcycle in a poorly ventilated room or covering it with a tarp, while it is still wet, will allow water and humidity to seep in and cause rust. [. . . ]