User manual YAMAHA MO6-MO8

[. . . ] OWNER'S MANUAL MUSIC PRODUCTION SYNTHESIZER EN SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. Battery Notice: This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement. [. . . ] Three separate EQ sections are available on the instrument: Element EQ, Part EQ, and Master EQ. Part EQ [PERFORM] Performance selection [EDIT] Part selection [F3] EQ [SONG]/[PATTERN] Song/Pattern selection [MIXING] [EDIT] Part selection [F3] EQ This 3-band EQ is applied to each part of the Performance/ Song/Pattern, The high band and low band are the shelving type. The middle band is the peaking type. Gain Q (frequency bandwidth) + 0 Frequency Element EQ [VOICE] Voice selection [EDIT] Element selection/Key selection [F6] EQ ­ 3 bands n LOW MID HIGH The part EQ is not available in the Voice mode. Master EQ [VOICE] Voice selection [UTILITY] [F3] VOICE [SF1] MEQ [PERFORM] Performance selection [EDIT] [COMMON] [F2] OUT/MEF [SF2] MEQ [SONG]/[PATTERN] Song/Pattern selection [MIXING] [EDIT] [COMMON] [F2] MEQ/MEF [SF1] MEQ Peaking type This type of EQ shape lets you attenuate/boost the signal at the specified Frequency setting. Gain + 0 Frequency Master EQ is applied to the final (post-effect), overall sound of the instrument. In this EQ, all bands can be set to peaking, or the lowest and highest bands can be set to shelving (as shown below). ­ Shelving type This type of EQ shape lets you attenuate/boost the signal at frequencies above or below the specified Frequency setting. Gain Low Gain High Gain EQ for which all bands are set to peaking type Gain Q (frequency bandwidth) + + 0 Frequency 0 Frequency ­ 3 bands LOW LOWMID MID HIGHMI HIGH ­ Low Freq n High Freq In addition to the individual gain controls, there is also an overall level parameter that attenuates/boosts the entire frequency range. EQ for which LOW and HIGH are set to shelving type Gain Q (frequency bandwidth) + 0 Frequency ­ 5 bands LOW LOWMID MID HIGHMID HIGH Owner's Manual 141 Basic Structure The Element EQ is applied to each element of the Normal Voice and each key of the Drum Voice. You can specify which shape is used among the two shapes described below and set the related parameters. Internal Structure (System Overview) Effect connection in each mode In the Voice mode The Effect parameters in the Voice mode are set for each Voice and the settings are stored as a User Voice. Note that the Master Effect and Master EQ parameters are set for all the Voices in the Utility mode. Once the Master Effect and EQ settings have been made, they can be stored as System settings by pressing the [STORE] button. [VOICE] Voice selection [EDIT] [COMMON] [F6] EFFECT [SF1] CONNECT System effects (Reverb effect and Chorus effect) Chorus Ctg, Chorus Typ (Chorus Effect Category, Chorus Effect Type) Reverb Typ (Reverv Effect Type) Determines the effect type for Chorus. Chorus Send, Reverb Send Determines the level of the sound (from Insertion A or B, or the bypassed signal) that is sent to Chorus/Reverb effect. Settings: 0 ­ 127 Chorus Return, Reverb Return Chorus Pan, Reverb Pan Determines the Return level and pan position setting for the Chorus/Reverb effect. Settings: 0 ­ 127, L63 (far left) ­ C (center) ­ R63 (far right) Tone Generator block Element 1-4 Effect Output EL: OUT 1-4 Insertion effects Ins A Ctgry, Ins B Ctgry (Insertion effect Category), Ins A Type, Ins B Type (Insertion effect Type) Chorus to Reverb Determines the Send level of the signal sent from the Chorus Effect to the Reverb Effect. Settings: 0 ­ 127 Basic Structure Element or Key Element EQ Determines which Insertion effect (A or B) is used to process each individual Element (Key). The "thru" setting lets you bypass the Insertion effects for the specific Element. Settings: insA, insB, thru Reverb Send Chorus Send Determines the effect type for Insertion A or B. Ins EF Connect (Insertion Effect Connect) Reverb Return Chorus Return Master effect [VOICE] [UTILITY] [F3] VOICE [SF2] MEF (for all Voices) Master EQ [VOICE] [UTILITY] [F3] VOICE [SF1] MEQ (for all Voices) [VOICE] Voice selection [EDIT] [COMMON] [F1] GENERAL [SF3] MEQ OFS Output Determines the effect routing for Insertion effects A and B. The setting changes are shown on the diagram in the display, giving you a clear picture of how the signal is routed. Settings Ins A to B A Ins B to A A Para A B B B 142 Owner's Manual Internal Structure (System Overview) In the Performance mode The Effect parameters in the Performance mode are set for each Performance. System effects (Reverb effect and Chorus effect) Chorus Ctg, Chorus Typ (Chorus Effect Category, Chorus Effect Type) Reverb Typ (Reverb Effect Type) Determines the effect type for Chorus. Chorus Send, Reverb Send Determines the level of the sound (from Insertion A or B, or the bypassed signal) that is sent to Chorus/Reverb effect. These parameters can be set in the Performance in the [F2] OUT/MEF display (*3). Settings: 0 - 127 Chorus Return, Reverb Return Chorus Pan, Reverb Pan Determines the Return level and pan position setting for the Chorus/Reverb effect. Settings: 0 - 127, L63 (far left) - C (center) - R63 (far right) Chorus to Reverb Determines the Send level of the signal sent from the Chorus Effect to the Reverb Effect. Settings: 0 ~ 127 [PERFORM] Performance selection [EDIT] [COMMON] [F6] EFFECT [SF1] CONNECT The Insertion connection type depends on the setting of the Voice assigned to the selected Part. *1 Part 1 Part EQ *2 *4 Master effect A B Master EQ Output [PERFORM] Performance selection [EDIT] [COMMON] [F2] OUT/MEF [SF3] MEF *1 Select the part to which the Insertion effect is applied. The Insertion effect depends on the setting of the Voice assigned to the selected part. [PERFORM] Performance selection [EDIT] [COMMON] [F6] EFFECT [SF2] INS SW *2 [PERFORM] Performance selection [EDIT] Part selection [F3] EQ *3 [PERFORM] Performance selection [EDIT] [COMMON] [F2] OUT/MEF [SF1] OUT *4 [PERFORM] Performance selection [EDIT] [COMMON] [F2] OUT/MEF [SF2] MEQ [PERFORM] Performance selection [EDIT] [COMMON] [F1] GENERAL [SF3] MEQ OFS Owner's Manual 143 Basic Structure Tone Generator block Part 1 Insertion Effect (VCE INS) *3 Reverb Send Chorus Send Reverb Return Chorus Return Internal Structure (System Overview) In the Song/Pattern mode The Effect parameters in the Song/Pattern mode are set for each Song/Pattern. System effects (Reverb effect and Chorus effect) Chorus Ctg, Chorus Typ (Chorus Effect Category, Chorus Effect Type) Reverb Typ (Reverb Effect Type) Determines the effect type for Chorus. Chorus Send, Reverb Send Determines the level of the sound (from Insertion A or B, or the bypassed signal) that is sent to Chorus/Reverb effect. [. . . ] 25/F. , United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. Tel: 714-522-9011 FRANCE Yamaha Musique France BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 HONG KONG Tom Lee Music Co. , Ltd. 11/F. , Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2737-7688 ITALY Yamaha Musica Italia S. P. A. Combo Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 INDONESIA PT. [. . . ]