User manual YAMAHA MG206C-USB-MG166CX-USB-MG166C-USB

[. . . ] Features Input Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 16 With up to 16 (MG166CX-USB/MG166C-USB: 10) mic/line inputs or up to four stereo inputs, the MG mixer can simultaneously connect to a wide range of devices: microphones, line-level devices, stereo synthesizers, and more. Compression. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9 Compression increases the overall level without introducing distortion by compressing excessive peaks in the signals from microphones and guitars. Cubase AI 4 DAW Software Supplied. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10 By connecting the MG mixer to the computer via a USB cable an audio data mixed by the MG mixer can be recorded on Cubase AI 4. High-quality digital effects (MG166CX-USB). . . . . . . . . . . pages 19, 23 With digital effects built in, the MG166CX-USB can deliver a wide range of sound variations all by itself. Caractéristiques Canaux d'entrée. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 64 Avec 16 entrées micro/ligne (MG166CX-USB/MG166C-USB: 10) ou quatre entrées stéréo maximum, la console de mixage MG peut connecter simultanément une grande variété d'appareils : micros, appareils de ligne, synthétiseurs stéréo, etc. [. . . ] Setting the knob to the "" position produces a flat response in the corresponding band. Turning the knob to the right boosts the corresponding frequency band, while turning to the left attenuates the band. The monaural channels have MID frequency controls to adjust the midrange frequency band. The following table shows the EQ type, frequency, and maximum cut/boost for each of the three bands. Band HIGH Type Shelving Peaking Shelving Frequency 10 kHz 2. 5 kHz* 100 Hz ±15 dB Maximum Cut/Boost To the INSERT I/O jack Sleeve (Ground) Ring: IN Tip: OUT Tip: OUT Tip: IN To the output jack of the external processor The signal output from the INSERT jacks is reverse-phased. This should not be a problem when connecting to an effect unit, but please be aware of the possibility of phase conflict when connecting to other types of device. A reversedphased signal may result in degraded sound quality or even complete sound cancellation. MID LOW CAUTION * The monaural channel MID frequency can be adjusted from 250 Hz to 5 kHz. The MID frequency is 2. 5 kHz when the MID frequency control is set at the center position. 6 GAIN Control Adjusts the input signal level. To get the best balance between the S/N ratio and the dynamic range, adjust the gain so that the PEAK indicator 9 lights only occasionally and briefly on the highest input transients. The -34 to +10 scale is the LINE input adjustment range. MG206C-USB/MG166CX-USB/MG166C-USB Owner's Manual 17 Reference Front & Rear Panels A AUX, EFFECT Control Adjusts the level of the signal sent from the channel to the AUX and EFFECT buses. These knobs should generally be set close to the "" position. These controls send either the signal from immediately prior to the channel fader (pre-fader signal) or the signal after the channel fader (post-fader signal) to the corresponding buses. The types of signals sent by the AUX and EFFECT controls on each mixer model are as follows: · MG206C-USB AUX1: Pre-fader AUX2, 3: Pre-fader/post-fader (determined by the AUX PRE switch B) AUX4: Post-fader · MG166CX-USB AUX1: Pre-fader AUX2: Pre-fader/post-fader (determined by the AUX PRE switch B) EFFECT: Post-fader · MG166C-USB AUX1: Pre-fader AUX2: Pre-fader/post-fader (determines by the AUX PRE switch B) AUX3: Post-fader NOTE D ON Switch Turn this switch on to send the signal to the buses. The switch lights orange when on. E PFL (Pre-Fader Listen) Switch This switch lets you monitor the channel's pre-fader signal. When the switch is on the channel pre-fader signal is output to the PHONES and MONITOR OUT jacks for monitoring. F 1-2 Switch This switch assigns the channel's signal to the GROUP 1/2 bus. NOTE To send the signal to the GROUP 1/2 bus turn the ON switch on ( ). G 3-4 Switch This switch assigns the channel's signal to the GROUP 3/4 bus. NOTE To send the signal to the GROUP 3/4 bus turn the ON switch on ( ). H ST Switch This switch assigns the channel's signal to the STEREO L/R bus. NOTE · To send the signal to the STEREO bus engage the ON switch ( ). · On stereo channels, the L (odd) and R (even) input signals are mixed and sent to the AUX and EFFECT buses. To send the signal to the STEREO bus turn the ON switch on ( ). I Channel Fader Adjusts the level of the channel signal. Use these faders to adjust the balance between the various channels. NOTE B AUX PRE Switch Selects whether the pre-fader or the post-fader signal is fed to the AUX buses. If the switch is on ( ), the mixer sends the pre-fader signal to the AUX buses, so that AUX outputs are not affected by the channel fader I. If the switch is off ( ) the mixer sends the post-fader signal to the AUX buses. Set the fader sliders for unused channels all the way down to minimize noise. C PAN Control PAN/BAL Control BAL Control The PAN control determines the stereo positioning of the channel signal on the GROUP 1/2 and GROUP 3/4 buses or on the STEREO L/R bus. The BAL control knob sets the balance between left and right channels. Signals input to the L input (odd channel) go to the GROUP 1 or 3 buses or to the STEREO L bus; signals input to the R input (even channel) go to the GROUP 2 or 4 buses or the STEREO R bus. NOTE On channels where this knob provides both PAN and BAL control, the knob operates as a PAN control when input is received via the MIC jack or L (MONO) input only, and as a BAL control when input is received via both L and R inputs. 18 MG206C-USB/MG166CX-USB/MG166C-USB Owner's Manual Reference Front & Rear Panels Digital Effects 1 * Only the MG166CX-USB has digital effects. 1 FOOT SWITCH Jack A Yamaha FC5 foot switch (sold separately) can be connected to this jack and used to toggle the digital effects ON and OFF. 2 PROGRAM Dial Selects one of the 16 internal effects. See page 23 for details about the internal effects. 2 3 3 PARAMETER Control Adjusts the parameter (depth, speed, etc. ) for the selected effect. The last value used with each effect type is saved. NOTE 4 When you change to a different effect type, the mixer automatically restores the value that was previously used with that type (regardless of the current position of the PARAMETER knob). [. . . ] COMPLETE AGREEMENT This Agreement constitutes the entire agreement between the parties with respect to use of the SOFTWARE and any accompanying written materials and supersedes all prior or contemporaneous understandings or agreements, written or oral, regarding the subject matter of this Agreement. No amendment or revision of this Agreement will be binding unless in writing and signed by a fully authorized representative of Yamaha. MG206C-USB/MG166CX-USB/MG166C-USB Owner's Manual 107 For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. [. . . ]