User manual YAMAHA MG06X/MG06

[. . . ] Owner’s Manual (this leaflet) • Included Accessories NOTE If you are using condenser microphones, turn on (O) the [PHANTOM +48V] switch. 1 Use the [REVERBN /O DELAY] switch to select Reverb (N) or Delay (O). Type REVERB HALL ROOM Description Reverb simulating a large space such as a concert hall. Echo suitable for vocals. 1 2 3 4 5 Quick Start Guide STEP 1 Connecting speakers, microphones, and instruments, etc. Connection Example Electric acoustic guitar Portable audio player Powered speakers Headphones Turn on the power to connected devices in the following order: (microphone), (instrument), (audio device) [ ] (switch on unit) (speakers) NOTICE Follow this order to avoid any loud, unexpected noise from the speakers. Reverse the order when turning the power off. PLATE DELAY SHORT LONG VO. ECHO 6 Set the [STEREO LEVEL] knob to the “3” position. 7 For channels to which a microphone is connected, set the [GAIN] knob to roughly the 12 o’clock position. Controls and Functions 2 [MIC/LINE] mono input jacks (channels 1/L, 2/R) 1 (Back panel) DC IN [12V] jack Connect the supplied AC power adaptor to this jack. Microphones Electric keyboard 6 [STEREO OUT] output jacks 1 6 7 Connect a powered speaker or powered amp. [. . . ] These precautions include, but are not limited to, the following: Power supply/AC power adaptor • Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. • Use the specified adaptor (MU18 or PA-130, or an equivalent recommended by Yamaha) only. Using the wrong adaptor can result in damage to the instrument or overheating. • If you intend to use the device in an area other than in the one you purchased, the included power adaptor may not be compatible. • Check the electric plug periodically and remove any dirt or dust which may have accumulated on it. Location • Do not place the device in an unstable position where it might accidentally fall over. • Do not place the device in a location where it may come into contact with corrosive gases or salt air. • When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn the power off and disconnect the plug from the outlet. Even when the power is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. Sound is faint, distorted, or noisy. Are □□ the [GAIN] knobs and [LEVEL] knobs of all relevant channels, and the [STEREO LEVEL] knob set too high?Lower the [GAIN] knobs of channels 1/L and 2/R, or turn on (O) the [PAD] switches. Set the [LEVEL] knobs of all relevant channels and the [STEREO LEVEL] knob to appropriate levels. If the volume of sound source is too loud, turning off the switches may result in distorted sound. Lower the volume of the connected device. *1 Noise is measured with A-weighting filter. Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corporation reserves the right to modify products or specifications at any time without prior notice. Since specifications, equipment, and options may not be the same in every locale, please check with your Yamaha dealer. Connections • Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. (class b korea) OBSERVERA!Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den ar ansluten till vägguttaget, även om själva apparaten har stängts av. ADVARSEL: Netspændingen til dette apparat er IKKE afbrudt, sålænge netledningen sidder i en stikkontakt, som er tændt — også selvom der er slukket på apparatets afbryder. VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta. (standby) Jack List (Pin Alignment) Input and Output Jacks Polarities Pin 1: Ground Pin 2: Hot (+) Pin 3: Cold (-) Tip: Hot (+) Ring: Cold (-) Sleeve: Ground Tip: L Ring: R Sleeve: Ground Balanced/Unbalanced Configurations Do not open • This device contains no user-serviceable parts. Do not open the device or attempt to disassemble the internal parts or modify them in any way. [. . . ] [Information on Disposal in other Countries outside the European Union] This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. (weee_eu_en_01) ■Connectors ■ XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-). 2 3 Information Turn the mixer right-side up, and mount it onto your microphone stand. Loosen the angle adjustment wingnut (1), adjust the mixer’s angle as desired (2), and then tighten the wingnut securely (3). ■About this manual ■ T yy he illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your device. T yy he company names and product names in this manual are the trademarks or registered trademarks of their respective companies. IMPORTANT NOTICE FOR THE UNITED KINGDOM The model number, serial number, power requirements, etc. , may be found on or near the name plate, which is at the bottom of the unit. [. . . ]