User manual YAMAHA MFC10

[. . . ] STATUS DATA/CTRL BANK MSB/MAX BANK LSB/MIN TOGGLE ON-OFF /NUMBER OF PGM DEC ±10 INC /NO /YES MEMORY EDIT FC EDIT WRITE /EXIT 2 Congratulations! Thank you for purchasing Yamaha's MFC10 MIDI Foot Controller. The MFC10 is a versatile MIDI foot control device that can transmit program changes and control changes to control effectors, tone generators, keyboards, MIDI guitars, rhythm machines, etc. . In addition to the onboard foot controller, up to 4 optional external foot controllers or switches can also be connected to the MFC10 for increased control versatility. In order to make full use of the MFC10's features and functions, we recommend that you read this manual thoroughly and keep it in a safe place for future reference. Contents Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Refer to the owner's manual of the receiving device for details on voice assignments. Refer to a GM voice map for the 128 voice allocations of GM MIDI devices. · BANK MSB (Bank Select MSB) · BANK LSB (Bank Select LSB) oFF , 000 ~ 127 Bank select numbers are used to access voices other than the 128 voices normally available in MIDI devices and GM devices. Program change data and bank select data (BANK MSB/ LSB:off, 000-127) must be transmitted together to access these voices. Refer to the owner's manual of the receiving device for specific information on bank select data. · The default settings for each memory (001-128) is as follows. STATUS=C0 (Channel Number 1), DATA/CTRL=001-128 (same as the memory number), BANK MSB/MAX=off, BANK LSB/MIN=off. 10 Normal Mode How to Edit Memory If the FUNCTION lamp is lit, press [FUNCTION], so that the lamp is off, and Program Change Memory is enabled. 1Select the Memory Number to be edited (see page 9). (The lamp above that foot switch and the STATUS lamp will flash. ) MEMORY EDIT 2Press [MEMORY EDIT] to cycle through the 4 edit parameters (the selected parameter's light will flash). · TOGGLE ON-OFF/NUMBER OF PGM can not be selected from Program Change Memory. MEMORY EDIT STATUS settings STATUS DATA/CONTROL settings DATA/CTRL BANK MSB/MAX BANK MSB settings BANK LSB settings BANK LSB/MIN TOGGLE ON-OFF /NUMBER OF PGM 3Use [INC/YES] and [DEC/NO] to edit the parameter. Press [INC/YES] to increase the value shown in the LED display by 1, press [DEC/NO] to decrease the value by 1. Hold the [INC/YES] button and press the [DEC/NO] button and the value shown in the LED display will increase by 10. Hold the [DEC/NO] button and press the [INC/YES] button and the value shown in the LED display will decrease by 10. Repeatedly press [INC/YES] to continue decreasing the value by 10. 001 DEC ±10 INC /NO /YES 128 128 DEC ±10 INC /NO /YES 001 DEC ±10 INC /NO /YES Increase by 10 Decrease by 10 DEC ±10 INC /NO /YES 4After the desired parameters have been edited in steps 2 and 3, press [WRITE/EXIT]. (The flashing number indicates confirmation is necessary to proceed or cancel saving of the edited data. ) · If data has not been edited, the Memory Number will not flash and the MFC10 will return to its normal control mode. WRITE /EXIT 007 5Press [INC/YES], to save the edited data to the current Memory Number, The MFC10 will return to its normal control mode. At this time the memory will revert to its pre-edited contents. DEC ±10 INC /NO /YES DEC ±10 INC /NO /YES · Another Memory Number from the same bank (10's digit bank) can be easily edited by pressing [1] - [0] without exiting from the edit mode. You must execute or cancel the save operation for the currently edited data (the current Memory Number will flash) before proceeding to edit the new number. If data has not been edited, the Memory Number will not flash and the newly selected Memory Number will be shown in the display. 11 Normal Mode Function Memory Press [FUNCTION], the FUNCTION lamp will light, and Function Memory is enabled. Function Memory stores and transmits MIDI data such as note on/off, control change, program change, song select, start, continue, stop, etc. , in its memory. There are 100 (F00-F99) memory allocations in which Function Data can be saved. · Press [FUNCTION] to enable to Program Change Memory. (The FUNCTION lamp is off. ) s Function Memory Control (Transmit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Function data is transmitted when a Memory Number is selected using the [1]-[0] and [x10] foot switches. A total of 100 (F00-F99) memory allocations are available for storing such data. Select a Memory Number To change and select the 1's digit. Press one of the [1]-[0] foot switches. F84 F81 Example: To change the Memory Number "F84" to "F81" press the [1] foot switch once. To change and select both the 10's and 1's digits. (The 10's digit of the LED flashes indicating input standby. ) Press [1]-[0], to select the 10's digit value. (The 1's digit flashes indicating input standby. ) Once again press [1]-[0] to select the 1's digit value. F23 F47 Example: To change the Memory Number "F23" to "F47", press [x10], [4], [7] in that order. 12 Normal Mode s Edit Function Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The following 9 types of MIDI data can be transmitted with Function Memory. The transmitting Channel Number and MIDI data can be stored to individual Memory Numbers. · Note On/Off (9) [STATUS=90-9F] DATA/CTRL BANK MSB/MAX BANK LSB/MIN TOGGLE ON-OFF /NUMBER OF PGM 90 ~ 9F 000-127 (Note Number) 001-127 (Note On Velocity) 001-127 (Note Off Velocity) Pn1-Pn4 (see page 18) Transmits keyboard Note On/Off data. If a different note is set to each foot switch, the foot switches can be used to play a scale. [. . . ] (In the case of error message 5, the internal memory may have some MISS, pressing [WRITE/EXIT] will automatically initialize the internal memory. ) Er1 MIDI Receive Error. After FE has been received, Note On data has been received but, no MIDI data was received within a 350 msec interval. ­>Check the cable and the condition of the transmitting device. ­>Reduce the volume of data being transmitted or transmit the data in smaller blocks. [. . . ]