User manual YAMAHA M7CL

[. . . ] M7CL Editor Owner's Manual Owner's Manual Special Notices · The software and this owner's manual are the exclusive copyrights of Yamaha Corporation. · Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. · Copying of the commercially available music sequence data and/or digital audio files is strictly prohibited except for your personal use. · Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software. [. . . ] This is linked with the STEREO/MONO MASTER section faders of the M7CL's panel. The current fader value is shown in the numeric box immediately below the fader. The numbers and alphabetical letters at the right of the fader indicate the mute groups to which that channel belongs, and show the Recall Safe and Mute Safe status of the channel. (For the significance of the numbers and alphabetical letters, see p. 15). J Channel number This is the channel number (ST or M). You can double-click this number to open the Selected Channel window for this channel. If you hold down the <Ctrl> key of your computer keyboard and double-click this, the Selected Channel window will open as an additional view. 21 M7CL Editor Owner's Manual DCA window In this window you can view and edit the parameters of DCA groups 1­8. You can access this window in the following ways. From the [Windows] menu, choose [Overview] and then choose "DCA" Use the navigation keys in the Master window to turn on the [DCA] button 1 2 A CUE This button cue-monitors all channels that are assigned to the DCA group. B ON If you turn this on, all channels assigned to the DCA group will be turned on. If you turn this off, no signal will be output from the channels assigned to the DCA group. C DCA fader 3 This fader adjusts the level of the DCA group. The current fader value is shown in the numeric box immediately below the fader. You can set this to the minimum value (­ dB) by holding down the <Ctrl> key of your computer keyboard and clicking the fader knob, or set it to the nominal value (0. 00 dB) by holding down the <Ctrl> key and <Shift> key and clicking the fader knob. If the fader is at nominal level, the green indicator at the right of the fader will light. If a DCA group is set to Recall Safe, the R character at the lower right of the fader is displayed in green. 4 5 D DCA number This is the number of the DCA group. E DCA group name This is a text box that displays the DCA group name. You can also edit the DCA group name in this text box. 22 M7CL Editor Owner's Manual Selected Channel window Here you can set the parameters of the currently selected input channel (INPUT CH 1­48 (*), ST IN channels 1­4) or output channel (MIX channels 1­16, MATRIX channels 1­8, STEREO/MONO channels). You can access this window in the following ways. From the [Windows] menu, choose [Selected Channel] and select "MAIN VIEW" Double-click the channel number in one of the Overview windows On the M7CL itself, assign one of the USER DEFINED KEYS to [1-16]/[17-32]/[33-48](*) in [SEL CH] of [M7CL EDITOR CONTROL], and execute the function NOTE By choosing [Selected Channel] from the [Windows] menu and then selecting "ADDITIONAL VIEW, " you can view a window for a channel that is not selected. This ADDITIONAL VIEW is not linked with [SEL] key operations on the panel of the M7CL. The type of parameters that can be edited in this window depends on the type of the currently selected channel. The parameters of the Selected Channel window are explained below, in the order of input channels (input channels 1­ 48, ST IN channels 1­4), MIX channels, MATRIX channels, and STEREO/MONO channels. (*) INPUT CH 33-48 can be viewed only if 48 is selected in the Input Channels field of the Mixer Setup window when editing offline, or when editing online with the M7CL-48. If an input channel is selected INPUT CH window 23 M7CL Editor Owner's Manual ST IN channel window NOTE Unless otherwise specified, the parameters explained below are common to INPUT CH 1­48 and ST IN channels 1­4. CHANNEL SELECT (Channel selection) 1 2 A SELECT (Channel selection) Indicates the number and name of the channel you are editing. To switch channels, use the SELECT button or the triangle buttons at left and right. The channel selected in the Main View is linked with the [SEL] keys in the INPUT section of the M7CL's panel. You can also edit the channel name in the text box. B INPUT PATCH Selects the input source assigned to the input channel (for the selectable input sources, p. 11). 24 M7CL Editor Owner's Manual MIX/MATRIX SEND 2 1 3 A MIX send level This adjusts the send level of the signal sent from the input channel to VARI-type MIX bus and MATRIX bus. The current value is shown in the numerical box immediately below. B PRE (Pre/Post) This selects PRE or POST as the point from which the signal is sent from the input channel to the MIX bus and MATRIX bus. The point will be PRE POINT when this is on, and POST FADER when this is off. The PRE POINT setting can be specified in the Mixer Setup screen. C ON (MIX send on/off) This is an on/off switch for the signal sent from the input channel to the MIX bus and MATRIX bus. HINT · If MIX buses or MATRIX buses are being used in stereo, the odd-numbered knob will be PAN. Knob of odd-numbered side Knob of oddnumbered side · If the FIXED type is selected for the MIX bus, only the ON button is valid. · The stereo/mono setting and the VARI type / FIXED type setting can be made in the Mixer Setup screen. HA GAIN/Ø/HPF 1 2 3 A HA (HA Gain) Adjusts the gain of the internal head amp or of the external head amp (AD8HR) patched to the input channel. [. . . ] In this case, you can re-save all scenes to a file after editing, recall just a desired scene, or copy a desired scene to the scene memory of the M7CL itself. 1 2 3 4 5 A File name Indicates the file name of the currently-open scene library. B OPEN (Open a file) Opens a scene library file located on a drive of your computer. C CLOSE (Close a file) Closes the currently-open scene library file. D SAVE 6 Saves the currently-open scene library file on a drive of your computer. E SAVE AS (Save as a different name) Saves the currently-open scene library file under a different name on a drive of your computer. 64 M7CL Editor Owner's Manual F FILE This area lists the scenes in the file you opened using the OPEN button (2). The list includes the following items. HINT To view items that are not currently shown, scroll the list to the right. 7 8 9 J K L M G No. This is the scene number. H TITLE This is the scene title. You can also double-click this area and edit the title. I PROTECT This indicates whether protect is on or off for each scene. This area displays a lock icon for protected scenes; these scenes cannot be overwritten, nor their title edited. [. . . ]