User manual YAMAHA IMX644

[. . . ] Owner's Manual SPECIAL NOTICES · The software and this manual are the exclusive copyrights of Yamaha Corporation. · Please read carefully the Software Licensing Agreement at the end of this manual before installing the software. · Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. · Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software. [. . . ] If the [LINK] button is on (green), this will be inoperable. Parameter Fader Level Range - ­ +10dB Default ­ Markers The red marker indicates the setting of the IMX644's volume knob; the blue marker indicates the volume value saved in memory. [LOCK] button If you turn this off (gray), operations of the volume knob for that channel will be effective if the IMX644 is locked by its LOCK switch. If this is on (red), volume knob operations for that channel will be ignored. 6 [MATRIX] button Opens the MATRIX screen (page 17). Here you can specify the output channels to which the input channel signals are sent. 7 [STEREO/MONO] button Specifies whether OUTPUT channels 1 and 2 deliver a STEREO or MONO output signal. When [STEREO] is selected the left (L) signal is output to channel A and the right (R) signal is output to channel B. 8 [EQ+FILTER] button Opens the OUTPUT EQ screen (page 19). Here you can edit the parameters of the 6-band equalizers provided for OUTPUT channels 1 through 4. 9 [DELAY] button Opens the "DELAY" dialog box, allowing you to specify the delay time for each OUTPUT channel. Use these settings when you need to apply a delay to the main speaker outputs so that the sound from the sub-speakers will not be heard with a timing offset. "DELAY" dialog box Time indication This specifies the delay time. Distance indication This indicates the specified delay time as a distance (meters) at the speed of sound (343. 59 m/s). Click the [ ]/[ ] buttons to edit the value. Parameter Time Indication Distance Indication Range 0 ­ 300msec 0 ­ 103. 08m Default 0msec 0m IMX644 Manager Owner's Manual 14 ) [BAL] button This opens the "BALANCE" dialog box, allowing you to specify the volume balance between outputs A/B (L/R) of OUTPUT channels 1 and 2. "BALANCE" dialog box Here you can adjust the volume balance between outputs A/B (L/R). Parameter Balance Range 0dB ­ -20. 1dB Default 0dB Right-click the [BALANCE] knob and continue holding down the mouse button to decrease the A (L) volume; left-click and hold down the mouse button to decrease the B (R) volume. Doubleclick to reset the value to center. Press (hold) the left button Press (hold) the right button !Output level meter, output SIGNAL/PEAK indicator Output level meters Displays the levels of the signal being output via OUTPUT channels 1 and 2. Output SIGNAL/PEAK indicators The SIGNAL/PEAK indicators show the output signal for OUTPUT channels 3 and 4. If the top segment (PEAK) of the level meter lights red, or if the PEAK indicator lights red, the output signal level is at the allowable maximum. Lower the input volume or the output volume. @ OUT 1­4, REC OUT These indicate the output channels and their names. Click a name to access the "Output Port Name" dialog box, where you can edit the name of the channel. # MEMORY [A]­[D] buttons When you click a button [A]­[D], the memory assigned to that button will be recalled and the parameter settings will be switched accordingly. This is the same function as the IMX644's MEMORY [A]­[D] buttons. Memories A through D all contain the same settings when the unit is shipped from the factory. IMX644 Manager Owner's Manual 15 INPUT screen Here you can edit the input channel parameters. 1 2 3 4 5 6 7 8 9 1 PAD When editing online, this will indicate "MIC" if the rear panel PAD (34 dB) switch is off, or "LINE" if the switch is on. When editing offline, this will indicate "MIC" by default. 2 +48V indicator When editing online, this will be dark if the rear panel +48V switch is off, or lit red if the switch is on. When editing offline this will be dark. 3 INPUT GAIN This edits the input gain value. Click the [-]/[+] buttons, or make changes in the dialog box that appears when you click the value. [. . . ] · Data received by means of the SOFTWARE may not be duplicated, transferred, or distributed, or played back or performed for listeners in public without permission of the copyright owner. · The encryption of data received by means of the SOFTWARE may not be removed nor may the electronic watermark be modified without permission of the copyright owner. 3. TERMINATION This Agreement becomes effective on the day that you receive the SOFTWARE and remains effective until terminated. If any copyright law or provisions of this Agreement is violated, the Agreement shall terminate automatically and immediately without notice from Yamaha. [. . . ]