User manual YAMAHA HTR-5930SIL

[. . . ] U HTR-5930 AV Receiver OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 10 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 11 · Explanation of Graphical Symbols 12 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 13 1 2 3 4 5 6 7 8 9 Read Instructions ­ All the safety and operating instructions should be read before the product is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. [. . . ] GUARD" in "OPTION MENU" is set to "ON" (see page 56). You can also select a decoder by pressing j / i on the remote control while the decoder type is displayed in the front panel display. 32 SOUND FIELD PROGRAMS For 2CH STEREO: Direct DIRECT Function: 2-channel stereo direct. Bypasses the decoders and DSP processors of this unit for pure hi-fi stereo sound when playing 2-channel analog sources. Choices: AUTO, OFF y · The "AUTO" setting bypasses the decoders and DSP processors only when "BASS" and "TREBLE" are set to 0 dB (see page 24). · When multi-channel signals (Dolby Digital and DTS) are input, they are downmixed to 2 channels and output from the front left and right speakers. · The low-frequency signals input from the front left and right speakers are redirected to the subwoofer in the following cases: ­ "BASS" is set to "BOTH" (see page 54). ­ "FRONT" is set to "SML" (see page 54) and "BASS" is set to "SWFR" (see page 54). Using Virtual CINEMA DSP Virtual CINEMA DSP allows you to enjoy the CINEMA DSP programs without surround speakers by creating virtual speakers. If you set "SURR" to "NONE" (see page 54), Virtual CINEMA DSP activates automatically whenever you select a CINEMA DSP program (see page 31). Note Virtual CINEMA DSP will not activate even when "SURR" is set to "NONE" (see page 54) in the following cases: ­ When "2CH STEREO" (see page 31) is selected or when this unit is in the "STRAIGHT" mode. ­ When the component connected to the MULTI CH INPUT jacks is selected as the input source (see page 25). ­ When headphones are connected to the PHONES jack. Listening to unprocessed input signals When this unit is in the "STRAIGHT" mode, multichannel sources are decoded straight into the appropriate channels without any additional effect processing. 2channel stereo sources are output from only the front left and right speakers. For PRO LOGIC II Music: Panorama PANORAMA Function: Sends stereo signals to the surround speakers as well as the front speakers for a wraparound effect. Choices: OFF, ON Dimension DIMENSION Function: Gradually adjusts the sound field either towards the front or towards the rear. Control range: ­3 (towards the rear) to +3 (towards the front), initial setting is STD (standard). Center width CT WIDTH Function: Adjusts the center image from all three front speakers to varying degrees. A larger value adjusts the center image towards the front left and right speakers. Control range: 0 (center channel sound is output only from center speaker) to 7 (center channel sound is output only from front left and right speakers), initial setting is 3. BASIC OPERATION 1 Press AMP on the remote control and then STRAIGHT to select "STRAIGHT". AMP STRAIGHT ENT. 2 To deactivate the "STRAIGHT" mode, press STRAIGHT on the remote control again so that "STRAIGHT" disappears from the front panel display. y You can also select "STRAIGHT" by pressing STRAIGHT on the front panel. 33 RECORDING RECORDING Recording adjustments and other operations are performed from the recording components. Notes · When this unit is set to the standby mode, you cannot record between other components connected to this unit. · The settings of TONE CONTROL (see page 24), VOLUME, speaker levels (see page 26) and the sound field programs (see page 31) do not affect recorded material. · The source connected to the MULTI CH INPUT jacks of this unit cannot be recorded. · Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording. Therefore, if your source component is connected to provide only digital signals, you cannot record the source. [. . . ] 2. 8 µV (20. 2 dBf) · Signal to Noise Ratio (IHF) Mono/Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 dB/70 dB · Harmonic Distortion (1 kHz) Mono/Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530/531 to 1710/1611 kHz [Other models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 V AC, 60 Hz [Australia model] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]