User manual YAMAHA FLUTES/PICCOLOS

[. . . ] Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. [. . . ] Applying excessive force to the cable may result in damage to the cable, such as the wires being severed, etc. * To customers who purchased a Pads Set, please refer to the attached "Accessories List" sheet included with the Pads Set when confirming package contents. Q TP65 main unit x 1, t clamp bolt x 1, y stereo phone cable x 1, u Owner's Manual (this sheet) x 1 w TP65S main unit* x 1, t clamp bolt x 1, y stereo phone cable x 1, u Owner's Manual (this sheet) x 1 e TP100 main unit* x 1, t clamp bolt x 1, y stereo phone cable x 1, u Owner's Manual (this sheet) x 1 r TP120SD main unit* x 1, y stereo phone cable x 1, u Owner's Manual (this sheet) x 1 TP65/65S Drum Pad Size: ø220 x 61(H) mm (excluding the clamp bolt) Weight: 980g (including the clamp bolt) Sensor System: [TP65] Trigger sensor (piezo) x 1 [TP65S] Trigger sensor (piezo) x 1, rim switch (2 zones) x 1 Output jack: [TP65] Standard mono phone jack [TP65S] Standard stereo phone jack TP100 Tom Pad (10") with rod clamp Size: 297 (W) x 313 (D) x 74 (H) mm (Control knob and clamp bolt not included. 2kg Sensor System: Trigger sensor (piezo) x 1, rim switch (2 zones) x 1 Output jack: Standard stereo phone jack TP120SD Snare Pad (12") Size: 349 (W) x 364 (D) x 69 (H) mm (Control knob not included. Si ce produit est utilisé avec le système de racks ou le support de cymbales, ne placez pas le rack ou le support sur une surface inclinée ou instable ou sur des marches. The function of the TP series pads varies according to which INPUT number on the DTX Series Drum Trigger Module the pad is connected. * For the users of the TP65/65S, connect to the input that is used for the tom pad on your drum trigger module. ) * For the users of the TP100/120SD , set the module's pad type setting as below. * When connecting the TP65S to the module, make sure a stereo phone cable is used. If a mono phone cable (plug has one black ring) is used, the voices assigned to the A/B rim switch will not be produced. ) The Pad control function is not available when a mono phone cable is used. * Using any stereo phone cable other than the supplied parallel type stereo phone cable can result in improper function of the pad control function. Also, please refer to the Owner's Manual that came with your DTX Series Drum Trigger Module for more information regarding the problems described above and any other problems that you may be experiencing. If a solution can not be found to the problem after consulting the manuals, please contact the dealer from whom you purchased the product. The pad controller on the TP100/120SD can be used with INPUTs 1-5 on the DTXTREME IIs or INPUT 1 on the DTXPRESS IV. (Please refer to the Owner's Manual that came with your module for more information. ) Never hit the controller knob or apply excessive force to it, since this may result in damage or malfunction. Do not put excessive pressure on the level adjustment knob; doing so may result in damage. When the TP100/120SD pad is used with a DTX Series Drum Trigger Module, enter the module's Trigger Setup Edit display and set the Gain (pad input level) parameter so that the display reads 90­95% when the pad is struck strongly. Refer to the Owner's Manual that came with your module for more information. [. . . ] Refer to the Owner's Manual that came with your module for more information. If the output level is too high, the pad's dynamic range (the difference between loud and soft sounds) will be reduced and problems such as double triggering (multiple triggers being produced by a single stroke) may occur. Rotate the level adjustment knob w to the right (looking at the knob from above) to increase the output level, or to the left to decrease it. The pad's output level should be adjusted depending on how hard you hit the pad, or to adjust the pad's dynamic range, or to better match the pad to the type of DTX Series Drum Trigger Module you are using. [. . . ]