User manual YAMAHA DTXPRESS IV SPECIAL SET ASSEMBLY MANUAL

[. . . ] Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. Clamps may be damaged and drums may drop, causing injury. Before assembling the unit, lay a drum mat (sold separately). Alternately, to prevent damaging your floor, lay the cardboard of the included packages, etc. on the floor before assembling the two parts shown in the circles in Figure 1. [. . . ] (Spare bands are included. ) Figure 6: Rack Assembly-4 RHH135 (Real Hi-Hat Pad) (1) Hi-Hat Clutch (1) Stand Base (1) Assembling the Rack System 1 Take out the rack system from the package and remove all the cushioning. Remove the bubble wrap on the pipes while assembling the rack system. WARNING If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. Do not let small children assemble or set up this product by themselves, or they may be injured. If this product is used with the rack system or a cymbal stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning. When setting the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall. The rack may overturn or be damaged, resulting in injury. The pipe ends may injure your fingers. Figure 3: Rack Assembly-1 HS650A (Hi-Hat Stand) (1) Stereo Phone Cable (1) Cable Band (1) 8 9 10 *1 YAMAHA logo label on the red curved pipe is facing the opposite side. Loosen the two knobs ((h) on the upper left) aligned at the base of pipe , and move pipe slightly outward in a clockwise direction. Loosen the two knobs ((j) on the middle right) aligned at the base of pipe and the in a knob ((k) on the lower right) of the slim pipe supporting pipe . Move pipe counterclockwise direction until it is about 90 degrees from the red curved pipe with the and YAMAHA logo label. Tighten the three knobs loosened and fix the position of pipe the slim pipe supporting it. Loosen the two knobs ((m) on the middle left) aligned at the base of pipe and the knob in a clockwise ((n) on the lower left) on the slim pipe supporting pipe , and move pipe direction until it is about 45 degrees from the red curved pipe with the YAMAHA logo and the slim pipe label. Tighten the three knobs loosened and fix the position of pipe supporting it. KP65 (Kick Pad) (1) Drum Key (1) Instruction Manual (4) - TP65/65S/100/120SD - PCY65/65S/135/155 - KP65 - RHH135 9-channel snake cable (1) Figure 9: Trigger Module DTXP4 (1) Wing Bolt (2) AC Adaptor 11 Check that the entire rack system is stable. Hold the upper area of the vertical pipe The pipes may bend when the area shown in collides. and , and shake them. If the rack system is unstable, retighten the knobs tightened in steps 2 to 5. Module Stand (1) Continued on the next page (on the back side) Mounting the pads and the trigger module on the rack system Mount the pads and the trigger module on the rack system. [. . . ] Tighten the clamp bolt and attach the 3-zone drum pad TP100 firmly. %1 Hi-Hat %2 KP65 (Kick Pad) #1 DTXP4 + Module stand #2 Clamp #3 Knob Attach the module stand (#1) onto the clamp (#2). Tighten the knob (#3) and fix the position. 4 5 6 Connecting the pads to the Trigger Module Connect the output jacks of the pad and the input jacks of the trigger module with the 9-channel snake cable. Figure 25: DTXP4 (Rear panel) ^1 Power supply jack (DC IN 12V) ^2 Cable clip ^3 Power switch 1 2 Make sure to turn the power off (the Standby/ On switch (^3) is set to the standby position ( )). Figure 29: Cable clip (DTXP4 rear panel) Assembling the KP65 (Kick pad) 1 If a drum mat (sold separately) is not available, lay a cardboard on the floor to prevent scratching the surface. 2 7 Figure 22: KP65 Assembly Figure 26: 9-channel Snake Cable Figure 30: Using Cable Band Attach the AC adaptor to connect to a power source. Insert the DC plug into the power supply jack (^1) and twist the cable around the cable clip (^2) to prevent the DC plug from falling out. Mounting the PCY135 and PCY155 (Cymbal pads) on the rack system Figure 14: Pads Assembly-3 Figure 15: Cymbal holder-1 3 Use the cable bands to bind the cables to the pipes at the six points shown with the circles. * Leaving the cable slacked may interfere with your performance. @1 @2 @3 @4 #4 #5 #6 #7 #8 Body Base Wing bolt Spring washer Washer * Each straight plug is labeled indicating the input jacks to which they are to be connected. 1 PCY155 Cymbal holder Wing nut Felt washer See Figure 15. [. . . ]