User manual YAMAHA DTX700K ASSEMBLY MANUAL

[. . . ] Before carrying out the procedures described below, ensure that you have correctly assembled the rack system as described in its assembly manual. Hi-hat clutch for the RHH135 (x1) Stoppers for the PCY135 (x2) Tuning key (x1) XP80 (Tom Pad) RHH135 (Real Hi-hat Pad) DTX700 Drum Trigger Module Clamp bolts (x4) XP70 and XP80 Owner's Manual (x1) KP65 Owner's Manual (x1) XP80 (Tom Pad) NOTICE Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, before setting up the HS650A Hi-hat Stand and KP65 Kick Pad, you can place the packages' cardboard boxes on the floor to protect it from damage. Cable band (x10) Felts for the PCY135 (x2) Cable band for the RHH135 (x1) Package 3: DTX700 DTX700 Drum Trigger Module (x1) Module stand (x1) AC power adaptor* (x1) 9-channel snake cable (x1) HS650 (Hi-hat Stand) KP65 (Kick Pad) XP80 (Snare Pad) RS500 (Rack System) PCY100, PCY135, and PCY155 Owner's Manual (x1) RHH135 Owner's Manual (x1) Assembly Manual (this pamphlet) Module stand fastening screws (x4) DTX700 Owner's Manual (x1) DTX700 Data List (x1) DVD (containing software) * May not be included depending on your particular area. Please check with your Yamaha dealer. PRECAUTIONS Before using, please read this assembly manual, and use this product in a safe and proper manner. * Please keep this manual in a safe place for future reference. [. . . ] · Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc. ) or high humidity (bathroom, outside on a rainy day, etc. ). Doing so may result in deformation, discoloration, damage or deterioration. · When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. 1. Attach the clamp bolt to the snare pad and provisionally tighten (by 5 or 6 turns). Clamp bolt (to be tightened in the direction shown) Snare pad (rear side) height and angle of the snare pad. When doing so, be sure to adjust one bolt at a time (i. e. , loosen a bolt, adjust the pad, and then retighten before loosening another). Clamp bolt B 3. If necessary, use clamp bolts A to D to adjust the height and angle of any of the pads. When doing so, be sure to adjust one bolt at a time (i. e. , loosen a bolt, adjust the pad, and then retighten before loosening another). Clamp bolt D Clamp bolt E Clamp bolt A Clamp bolt A Clamp bolt C Clamp bolt C Clamp bolt D Clamp bolt B * Specifications and descriptions in this owner's manual are for information purposes only. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. Continued on other side Mounting the drum trigger module and cymbal pads PCY135 Assembling the kick pad Mounting the cymbal pads PCY135 1. Using a tuning key, loosen the stopper's key bolt. 5. With the stopper making full contact with the bottom surface of the bolt cover, tighten the stopper's key bolt using a tuning key. 1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from scratching. and line up each set nearby in the order in which it was removed. Spring washer Wing bolt Washer 2. Remove the wing bolts, spring washers, and washers from the kick pad frame, 3. [. . . ] Ensure, therefore, that these cables are not bent at an extreme angle when wrapped around the clips. Assembling the hi-hat stand 6 5. As shown on the right, loosen the wing bolt (b in the figure) to remove the hi-hat clutch. * This hi-hat clutch is not used within the standard assembly example shown in this pamphlet. Instead, use the hi-hat clutch that came with your RHH135. Hi-hat clutch Felt washer Connect the drum trigger module to a power supply. 1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from scratching. [. . . ]