User manual YAMAHA DTX550K ASSEMBLY MANUAL

[. . . ] Doing so may result in deformation, discoloration, damage or deterioration. · When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. [. . . ] Insert the rubber foot on each further end of pipe and . PCY155 (Cymbal Pad) (1) RHH135 (Real Hi-Hat Pad) (1) Stopper (2) Figure 6: Rack Assembly-4 PRECAUTIONS Before using, please read this assembly manual, and use this product in a safe and proper manner. Particularly in the case of children and young users, parents or an instructor should teach the children the proper manner in which to use the device. Assembling the Electronic Drum Rack 1 H C J D KP65 (Kick Pad) (1) Hi-Hat Clutch (1) Stand Base (1) CAUTION Take out the electronic drum rack from the package and remove all the cushioning. Remove the bubble wrap on the pipes while assembling the electronic drum rack. The pipe ends may injure your fingers. E Drum Key (1) HS650A (Hi-Hat Stand) (1) WARNING If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. Figure 3: Rack Assembly-1 · Do not let small children assemble or set up this product by themselves, or they may be injured. · Be careful with the edges of the cymbal holders and the tom holders. · If this product is used with the electronic drum rack or a cymbal stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning. · When setting the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall. The rack may overturn or be damaged, resulting in injury. *1 YAMAHA logo label on the curved pipe is facing the opposite side. *2 The knob is on the opposite side of the pipe. 8 9 Cable Band (1) See Figure 6. Loosen the two knobs ((h) on the upper left) aligned at the base of pipe , and move pipe slightly outward in a clockwise direction. Loosen the two knobs ((j) on the middle right) aligned at the base of pipe and the knob ((k) on the lower right) of the slim pipe supporting pipe . Move pipe in a counterclockwise direction until it is about 90 degrees from the curved pipe with the YAMAHA logo label. Tighten the three knobs loosened and fix the position of pipe and the slim pipe supporting it. Loosen the two knobs ((m) on the middle left) aligned at the base of pipe and the knob ((n) on the lower left) on the slim pipe supporting pipe , and move pipe in a clockwise direction until it is about 45 degrees from the curved pipe with the YAMAHA logo label. Tighten the three knobs loosened and fix the position of pipe and the slim pipe supporting it. 9-Channel Snake Cable(1) Owner's Manual (4) - TP65/65S/100/120SD - PCY65/65S/135/155 - KP65 - RHH135 Figure 9: Trigger Module DTX500 (1) Wing Bolt (2) Module Stand (1) AC Adaptor(1) DTX500 Owner's Manual(1) 10 NOTICE The pipes may bend when the area shown in collides. [. . . ] Tighten the knob (#3) and fix the position. ^1 DC IN terminal (12V) ^2 Cable clip ^3 Standby/On Switch 4 5 6 1 Connecting the pads to the Trigger Module Connect the output jacks of the pad and the input jacks of the trigger module with the 9-channel snake cable. Figure 26: DTX500 (Rear panel) Make sure to turn the power off Standby/ On Switch (^3) is set to the standby position ( )). Figure 30: Cable clip (DTX500 rear panel) 2 2 7 Assembling the KP65 (Kick pad) 1 If a drum mat (sold separately) is not available, lay a cardboard on the floor to prevent Figure 23: KP65 Assembly scratching the surface. Attach the AC adaptor to connect to a power source. Insert the DC plug into the DC IN terminal (^1) and twist the cable around the cable clip (^2) to prevent the DC plug from falling out. Mounting the PCY135 and PCY155 (Cymbal pads) on the electronic drum rack Figure 15: Pads Assembly-3 Figure 16: Cymbal holder-1 Figure 31: Using Cable Band Figure 27: 9-channel Snake Cable 3 Use the cable bands to bind the cables to the pipes at the points shown with the circles. @0 @1 @2 @3 @4 1 PCY135 PCY155 Cymbal holder Wing nut Felt washer #4 #5 #6 #7 #8 2 Body Base Wing bolt Spring washer Washer See Figure 16. [. . . ]