User manual YAMAHA DTX532K/DTX562K ASSEMBLY MANUAL

[. . . ] Push the snare pad onto the rack’s snare holder. Ensure that the snare holder’s rod is fully inserted into the snare pad’s mounting hole, and then tighten the clamp bolt to secure the pad in place. Snare pad Snare holder Rod  Tom pads WARNING Failure to observe the precautions described below can result in serious injury or even death. CAUTION Failure to observe the precautions described below can result in injury and/or property damage. 1. As with the snare pad, attach a wing bolt (DTX532K) or clamp bolt (DTX562K) to each of the three tom pads and provisionally tighten (by five or six turns). Each time, ensure that the tom holder’s rod is fully inserted into the tom pad’s mounting hole, and then tighten the bolt to secure the pad in place. • Young children using this electronic drum kit should be supervised by a guardian to eliminate any possibility of injury. In order to avoid injury, therefore, you should take special care whenever handling these components. [. . . ] Push each of the tom pads onto one of the rack’s Push on Clamp bolt DTX532K Tom pad: TP70 Rod DTX562K Tom pad: XP70 Rod NOTICE: Usage Precautions • When connecting and disconnecting cables, be sure to hold the plug and not the cable itself. In addition, avoid placing heavy items on top of cables and do not allow them to touch sharp edges. Failure to avoid these precautions can lead to cable breakage and disconnection. • Do not climb onto the electronic drum kit and avoid placing heavy objects on it. • Avoid using or storing the electronic drum kit in very hot locations (i. e. , in direct sunlight, in close proximity to a heater, or in a closed vehicle) or in highly humid locations (i. e. , in a bathroom or outdoors in wet weather). Failure to observe this precaution can lead to warping, discoloration, malfunction, or breakdown. • Avoid cleaning the electronic drum kit with organic solvents, paint thinner, or alcohol as these substances can cause warping and discoloration. Instead, we recommend you remove dust using a soft dry cloth or wipe clean using a moist, tightly-wrung cloth. If the electronic drum kit is very dirty, first wipe the dirt away using a cloth moistened with a neutral detergent solution and tightly wrung. Following this, wipe away the detergent solution using a cloth soaked in water and tightly wrung. XP80 Snare Pad 3. Loosen bolts A to D as shown below to adjust the height and angle of the snare pad’s playing surface. When correctly positioned, be sure to securely retighten the bolts before proceeding to the next step. Bolt B Bolt D Bolt C Bolt A Wing bolt Push on Tom holder Clamp bolt Push on Tom holder  Snare pad 1. Attach a clamp bolt to the snare pad and provisionally tighten (by five or six turns). Clamp bolt (tighten in the direction of the arrow) Underside of snare pad 3. Loosen bolts A to C as shown below to adjust the height and angle of each tom pad’s playing surface. When correctly positioned, be sure to securely retighten the bolts before proceeding to the next step. Bolt B Bolt A Bolt C * DTX562K shown. * Yamaha Corporation reserves the right to change or modify products or specifications at any time without prior notice. Continued on rear. Assembling the drum module and cymbal pads PCY135 Cymbal Pad PCY135 Cymbal Pad Assembling the kick pad  Each cymbal pad 5. [. . . ] In such a case, loosen the key bolt as much as possible without removing it. The second felt pad removed from the cymbal holder in Step 2 above is not required for assembly. 9. Tighten the wing nut to secure the pad to the cymbal holder. Stopper Cymbal pad Smaller hole Wing nut Felt pad that came with cymbal Plug the straight ends of the nine-channel snake cable into the trigger input jacks ([qSNARE] to [oHI-HAT] and [HI-HAT CONTROL]) on the back of the drum module. • When using the standard setup, the stickers on each of the snake cable’s plugs will indicate the name of the corresponding pad. 2. [. . . ]