User manual YAMAHA DTX520K ASSEMBLY MANUAL

[. . . ] Before carrying out the procedures described below, ensure that you have correctly assembled the rack system as described in its assembly manual. · Although this pamphlet uses illustrations of the DTX540K, the assembly procedures described also apply to the DTX520K. XP80 (Tom Pad) Felts for the PCY100 (x2) Hi-hat holder (x1) Stoppers for the PCY100 and PCY135 (x3) Felts for the PCY135 (x1) XP70 and XP80 Owner's Manual (x1) KP65 Owner's Manual (x1) PCY100 (Hi-hat Pad) XP70 (Tom Pad) Package 2: DTP520P (for DTX520K) XP80 Snare Pad (x1) TP65 Tom Pad (x3) Clamp bolts (x4) KP65 Kick Pad (x1) DTX500 Drum Trigger Module NOTICE Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, before setting up the HH65 Hi-hat Controller and KP65 Kick Pad, you can place the packages' cardboard boxes on the floor to protect it from damage. Tuning key (x1) XP70 and XP80 Owner's Manual (x1) KP65 Owner's Manual (x1) TP65, TP65S, TP100, and TP120SD Owner's Manual (x1) XP80 (Snare Pad) RS500 (Rack System) KP65 (Kick Pad) HH65 (Hi-hat Controller) Cable band (x10) 9-channel snake cable (x1) Package 3: DTX500 DTX500 Drum Trigger Module (x1) AC power adaptor* (x1) Module stand (x1) Module stand fastening screws (x2) PCY100, PCY135, and PCY155 Owner's Manual (x1) HH65 Owner's Manual (x1) Assembly Manual (this pamphlet) DTX500 Owner's Manual (x1) * May not be included depending on your particular area. [. . . ] · Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc. ) or high humidity (bathroom, outside on a rainy day, etc. ). Doing so may result in deformation, discoloration, damage or deterioration. · When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. Left leg b Left leg b * Specifications and descriptions in this owner's manual are for information purposes only. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. Continued on other side Mounting snare and tom pads DTX540K: XP70 DTX520K: TP65 Assembling the kick pad 2. As shown below, ensure that the rod section is fully inserted into the pad's mounting hole, and then fully tighten the clamp bolt. Clamp rod Rod section Snare pad Mounting the tom pad 1. 1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from scratching. and line up each set nearby in the order in which it was removed. Spring washer Wing bolt Washer As with the snare pad, attach the clamp bolt to each of the three tom pads and provisionally tighten (by 5 or 6 turns). As shown below, ensure that the rod section is fully inserted into each pad's mounting hole, and then fully tighten the clamp bolt. Tom pad Rod section Clamp rod 2. Remove the wing bolts, spring washers, and washers from the kick pad frame, 3. Join the base section to the frame as shown right, and then secure it in place by assembling the wing bolts, spring washers, and washers removed in the previous step from the base side. Body 2. Mount the three tom pads on the rack's clamp rods. Body XP80 Insert Clamp bolt Base Support plate Insert Mounting the snare pad 3. [. . . ] Place the stopper on the cymbal holder. * If the key bolt was not sufficiently loosened in Step 1 above, it may not be possible to pass the stopper over the cymbal holder's shaft. In such a case, loosen the key bolt as much as possible without removing it. 8. Assemble the felt pad that came with your pad unit. * The second felt pad removed from the cymbal holder in Step 2 above is not required for assembly of your pad unit. Ensure that the (Standby/On) button is set to the Standby position, and then connect the AC power adaptor to the DC IN jack on the rear panel. [. . . ]