User manual YAMAHA DSP-E390

[. . . ] DSP-E390 Natural Sound Digital Sound Field Processor 4 Programs for Digital Sound Field Processing 2 Programs for Dolby Surround (DOLBY PRO LOGIC and ENHANCED) 60W (8) RMS Output Power, 0. 1% THD, 1 kHz (Center Channel Power Amplifier) 15W + 15W (8) RMS Output Power, 0. 7% THD, 1 kHz (Rear Channel Power Amplifier) Automatic Input Balance Control for Dolby Surround Test Tone Generator for Easier Speaker Balance Adjustment 3 Center Channel Modes (NORMAL/WIDE/PHANTOM) Remote Control Capability Thank you for selecting this YAMAHA digital sound field processor. OWNER'S MANUAL CAUTION RISK OF ELECTRIC SHOCK CONTENTS Safety Instructions . . . . . . . . . . . . . . . . . . . 4 Speaker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Speaker Balance Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. IMPORTANT! [. . . ] With some subwoofers, including the Yamaha Active Servo Processing Subwoofer System, the amplifier and subwoofer are in the same unit. REAR OUTPUT terminals These terminals are for rear channel line output. There is no connection to these terminals when you use the built-in amplifier. However, if you drive rear speakers with an external stereo power amplifier, connect the input terminals of the external amplifier (MAIN IN or AUX terminals of a power amplifier or an integrated amplifier) to these terminals. CENTER OUTPUT terminal This terminal is for center channel line output. There is no connection to this terminal when you use the built-in amplifier. However, if you drive a center speaker with an external power amplifier, connect the input terminal of the external amplifier to this terminal. OUTPUT LOW PASS fc:200Hz CENTER OUT REAR OUT Subwoofer system FRONT LEVEL switch Normally set to "0 dB". If desired, you can decrease the output level at the FRONT OUT terminals by 10 dB by setting this switch to "­10 dB". (Refer to "Notes" on page 11. ) -l0dB 0 dB FRONT LEVEL 8 IDENTIFICATION OF CONTROLS FRONT PANEL NATURAL SOUND DIGITAL SOUND FIELD PROCESSOR DSP­E390 l DIGITAL SOUND FIELD PROCESSOR TEST CENTER MODE PROGRAM EFFECT TAPE MONITOR POWER DELAY PRO LOGIC ENHANCED WIDE ms VOLUME l8 20 24 28 34 CENTER LEVEL REAR LEVEL 40 50 l6 l4 l2 l0 8 6 4 3 2 70 0 I0 0 I0 ­dB 0 l CINEMA DSP 60 1 2 3 4 5 6 78 90 A REMOTE CONTROL TRANSMITTER 1 TAPE MONITOR 0 2 3 4 POWER Turns the power on/off. Display panel Displays your selection on the DSP or other information. Remote control sensor Receives signals from the remote control transmitter. (See pages 10­11. ) CENTER LEVEL Adjusts center speaker sound output level. (See page 10. ) PROGRAM Selects a program from the digital sound field processor. (See pages 12­14. ) 8 9 0 REAR LEVEL Adjusts rear speaker sound output level. (See page 14. ) EFFECT ON/OFF Switches on/off the digital sound field processor. (See page 14. ) TAPE MONITOR Used when the tape deck is connected to this unit's TAPE terminals to select that tape as the input source. HALL CNCT VIDEO MONO MOVIE ROCK ON/OFF EFFECT TEST CENTER MODE 9 6 A DELAY TIME MASTER VOLUME + ­ + ­ 5 6 7 A B 9 SPEAKER BALANCE ADJUSTMENT This procedure lets you adjust the sound output level balance between the front, center, and rear speakers using the built-in test tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor. 2 53 1 PROGRAM 4 6 PRO LOGIC -- ENHANCED SUR. HALL CNCT VIDEO MONO MOVIE ROCK ON/OFF EFFECT TEST CENTER MODE DELAY TIME MASTER VOLUME 3 5 + + ­ 64 1 5 ­ Select the center channel output mode according to your speaker configuration. (Refer to "SPEAKER CONFIGURATION" on page 5. ) CENTER MODE NORMAL WIDE PHANTOM Set to the " " position. 2 Turn on the power of this unit and the amplifier etc. POWER On the feature of each mode, refer to the "Notes" shown below. 6 TEST NORMAL WIDE PHANTOM 3 ms TEST Turn the DSP on, so that a DSP program name appears on the display. EFFECT Flashes continuously. CONCERT HALL 4 Select the PRO LOGIC or PRO LOGIC ENHANCED mode, so that the corresponding name is illuminated on the display. Notes q In step 5, when you select the center channel output mode, note the following. For 5 speaker configuration) NORMAL: Select this mode when you use a center speaker that is smaller than the front speakers. WIDE: Select this mode when you use the center speaker approximately same sized as the front speakers. For 4 speaker configuration) PHANTOM: Select this mode when you do not use the center speaker. [. . . ] In this case, reposition the main unit to avoid direct lighting. 15 TROUBLESHOOTING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM The unit fails to turn on when the POWER switch is pressed. The protection circuit has been activated because of short circuit etc. The power to the component connected to the REC OUT terminals of this unit is off. [. . . ]