User manual YAMAHA DME64N

[. . . ] Explanation of Graphical Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 Read these instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] The Status Icons A word clock signal is present, and this signal can be selected as the DME64N/24N word clock. No word clock signal (cannot be selected as the master clock). Word Clock Setup (WCLK) Page Shows the status of incoming word clock signals, and allows setup of the DME64N/24N master word clock. NO T E This page will not be displayed on the ICP1. A word clock signal is present, but is not in sync with the master word clock. Currently selected as the DME64N/24N word clock, but the clock signal is not useable. Inactive slot channel, or no I/O card is present in the slot. 1 2 3 4 5 Slot Information (Slot) Page Displays the name of the card installed in an I/O card slot. Some cards can also be reset via this page. Master Clock Selection Procedure 1. Use the cursor [E], [ ], [ ], [F] keys to select one of the square blocks representing the available master clock sources. 2. Press the [ENTER] key to select the master clock. NOTE 2 1 3 This page will not appear on the ICP1 display. 2 Int Sets the frequency of the internal word clock ­ 44. 1 kHz, 48 kHz, 88. 2 kHz, or 96 kHz. 3 WCIN Shows the status of the word clock signal at the [WORD CLOCK IN] connector. 4 Cascade Shows the status of the word clock signal at the [CASCADE IN] and [CASCADE OUT] connectors. No Display (Default): 44. 1/48 kHz audio signal transfer. SP (Double Speed): An 88. 2/96 kHz capable card is installed, allowing direct transfer at 88. 2 or 96 kHz. CH (Double Channel): A 44. 1/48 kHz card is installed, and 88. 2 or 96 kHz audio is transferred by using two 44. 1/48 kHz channels to transfer each channel of 88. 2/96 kHz audio. The number of audio channels that can be handled in this mode is half the number of channels normally handled by the card. DME64N/DME24N Owner's Manual 49 Panel Operation and Displays 1 Fs The current sampling frequency of the master word clock. The value shown here is determined by the system's master word clock signal. To select the word clock to be used as the master, move the cursor to the appropriate word clock indication in this display ­ the [WORD CLOCK IN] clock, the cascade clock, or a slot clock, for example ­ and press the [ENTER] key. 1 Card Name The name of the installed card appears here. The input setting is on the left and the output setting is on the right. Utility Displays MIDI Setup (MIDI) Page 3 1 2 4 5 6 NO T E This page will not appear on the ICP1 display. NOTE "DAW" stands for "Digital Audio Workstation. " ProTools, Logic, and Cubase are DAW applications, and this parameter provides direct compatibility with a number of physical controls surfaces that are available for use with these DAW software packages. The following parameters are available when the DAW parameter is set to OFF. 3 CH Specifies the device's MIDI transmit and receive channel: 1 ~ 16. Edit using the "List Parameters" editing procedure described on page 37. 4 Program Change Turns transmission and reception, the omni mode, and echo ON or OFF for MIDI program change messages. Move the cursor to the required parameter, then press the [ENTER] key to alternately turn ON and OFF. 5 Control Change Turns transmission and reception, the omni mode, and echo ON or OFF for MIDI control change messages. Move the cursor to the required parameter, then press the [ENTER] key to alternately turn ON and OFF. 6 Parameter Change Turns transmission and reception, and echo ON or OFF for MIDI parameter change messages. [. . . ] 31 Z zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 74 DME64N/DME24N Owner's Manual For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. [. . . ]