User manual YAMAHA DME24N

[. . . ] DIGITAL MIXING ENGINE Owner's Manual EN Explanation of Graphical Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 Read these instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] Edit using the "List Parameters" editing procedure described on page 38. NOTE When the DME64N/24N is functioning as the device group master and is connected to a computer running the DME Designer application via USB, the MIDI port being used by the DME Designer will not be available. Ext HA Ctrl (External head amp control) Displays/sets the type of connection to be used for external head amp control. Always use this setting when a remote head amp unit (AD8HR, AD824) is connected. Also, don't change the setting while a remote head amp is connected. Doing so can damage the unit. COM Displays/sets the type of connection to be used for DME communication Protocol. Normally, set this to "OFF". DME64N/DME24N Owner's Manual 49 Panel Operation and Displays Utility Displays Protocol (MIDI Protocol Setup) Displays/sets the protocol to be used for communication with devices connected via MIDI. MIDI: Use this setting when any MIDI device other than a general-purpose ProTools controller (HUI protocol) or general-purpose Logic or Cubase controller (Mackie control protocol) is to be connected. DAW (Type1): Use this setting when a generalpurpose ProTools controller (HUI protocol) is to be connected. DAW (Type2): Use this setting when a generalpurpose Logic or Cubase controller (Mackie control protocol) is to be connected. Edit using the "List Parameters" editing procedure described on page 38. Refer to the DAW controller owner's manual as well as the DME Designer manual for setup details. NOTE "DAW" stands for "Digital Audio Workstation. " ProTools, Logic, and Cubase are DAW applications, and this parameter provides direct compatibility with a number of physical controls surfaces that are available for use with these DAW software packages. Word Clock Setup (WCLK) Page Shows the status of incoming word clock signals, and allows setup of the DME64N/24N master word clock. NOTE This page will not be displayed on the ICP1. Master Clock Selection Procedure 1. Use the cursor [ E ], [ ], [ ], [ F ], buttons to select one of the square blocks representing the available master clock sources. Press the [ENTER] button to select the master clock. 2. Fs The current sampling frequency of the master word clock. The value shown here is determined by the system's master word clock signal. To select the word clock to be used as the master, move the cursor to the appropriate word clock indication in this display ­ the [WORD CLOCK IN] clock, the cascade clock, or a slot clock, for example ­ and press the [ENTER] button. The following parameters are available when the Protocol parameter is set to MIDI. CH Specifies the device's MIDI transmit and receive channel: 1 ~ 16. Edit using the "List Parameters" editing procedure described on page 38. Int Sets the frequency of the internal word clock ­ 44. 1 kHz, 48 kHz, 88. 2 kHz, or 96 kHz. Program Change Turns transmission and reception, the omni mode, and echo ON or OFF for MIDI program change messages. Move the cursor to the required parameter, then press the [ENTER] button to alternately turn ON and OFF. WCIN Shows the status of the word clock signal at the [WORD CLOCK IN] connector. Control Change Turns transmission and reception, the omni mode, and echo ON or OFF for MIDI control change messages. Move the cursor to the required parameter, then press the [ENTER] button to alternately turn ON and OFF. Cascade Shows the status of the word clock signal at the [CASCADE IN] and [CASCADE OUT] connectors. Panel Operation and Displays Parameter Change Turns transmission and reception, and echo ON or OFF for MIDI parameter change messages. Move the cursor to the required parameter, then press the [ENTER] button to alternately turn ON and OFF. 50 DME64N/DME24N Owner's Manual Utility Displays SLOT1~4 Shows the status of the word clock signal input via I/O cards installed in the I/O slots. The Status Icons A word clock signal is present, and this signal can be selected as the DME64N/24N word clock. A word clock signal is present, but is not in sync with the master word clock. [. . . ] 16, 32 word clock master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 word clock slave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Z zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 DME64N/DME24N Owner's Manual 75 MEMO 76 DME64N/DME24N Owner's Manual MEMO DME64N/DME24N Owner's Manual 77 MEMO 78 DME64N/DME24N Owner's Manual For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. [. . . ]