User manual YAMAHA DG-STOMP

[. . . ] This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Failure to follow instructions could void your FCC authorization to use this product in the USA. [. . . ] Hold Foot Switch 2 for more than one second to decrease the group number by a value of one. When the Group number is changed, the Foot Switch's lamps will flash. Hold Foot Switch 3 for more than one second to increase the group number by a value of one. When the Group number is changed, the Foot Switch's lamps will flash. Press a Foot Switch (1-3) to select the corresponding bank number (1-3). When a BANK is selected, the lamp in the display and foot switch lamp will flash quickly. Press a Foot Switch (1-3) at this time to select the corresponding patch number (1-3). * To cancel the selected patch, press the BANK switch. It will return to the previous condition. MIDI OUT MFC10, etc 2. Match the DG-Stomp's MIDI receive channel with the MIDI transmit channel on the external MIDI device. page 24 [Set the MIDI Receive Channel] 3. = 1:011, 2:012. . . 128:4. 12) page 24 [Create a Program Change Table] * This operation is used to assign patch numbers to a corresponding program change number received from an external device. For example, when the program change number "1" is received, the DG-Stomp's patch number "113" is recalled. 4. When program change data is transmitted from an external MIDI device, the patch is selected that corresponds to the program change table you created. * Refer to the owner's manual for your external MIDI device for instructions on how to transmit program change data. 16 Using the DG-Stomp s Create and Store a Patch Original settings can be stored in the USER AREA (011-933). Try creating an original patch and then store it. s Convenient Functions Here are some convenient functions that you can use with the DG-Stomp. q Storing Procedure 1. Press the [STORE] button. When you enter the Store Mode, the display, the [STORE] lamp and the foot switch lamp corresponding to the patch number will flash. q Use Foot Switches 1-3 to Switch Effects ON/OFF You can set Foot Switch 1 to act as an ON/OFF switch for the modulation effect, Foot Switch 2 as an ON/OFF switch for the delay effect, and Foot Switch 3 as an ON/OFF switch for the reverb effect. 2. Select the patch (group, bank, patch number) to which you want to store the patch. Use the same procedure as described in [Try Selecting Another Patch] (page 15) to select a patch. You can use the [UP]/[DOWN] buttons, the foot switches and the BANK switch to select the patch number. However, you cannot change the AREA (it can only be assigned to the USER AREA). Modulation Effect Delay Effect Reverb Effect 3. After select the patch you want to store your patch in, hold the [STORE] button. The store operation is complete when all lamps light. * Utility mode settings are not stored with patch data. As common settings for all patches, their contents are stored in the DG-Stomp memory. Use the MASTER knob to set differences in volume for situations like backing, soloing, etc. * Data in the USER AREA (011-933) can be stored in an external MIDI device. [. . . ] q Set the High Frequency of the Wah Pedal Sets the high frequency in the wah pedal's frequency range. Press the [CHORUS] button and use the [UP]/ [DOWN] buttons to set the frequency (1. 5 0- s Preamp Circuit ON/OFF Settings When the DG-Stomp's preamp circuit is not used, it is possible to use the DG-Stomp as an effector or a MIDI foot controller. · on : The preamp circuit is active (in use) · oFF : The preamp circuit is inactive (not in use) 5. 00:kHz). q Set the Wah Pedal "Q" Sets the frequency curve of the wah pedal. [. . . ]