User manual YAMAHA CVP-900 1

[. . . ] CVP-900 OWNER'S MANUAL CVP-900 OWNER'S MANUAL OWNER'S MANUAL Introduction SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. Please observe all cautions indicated on this page and those indicated in the safety instruction section. Battery Notice: This product MAY contain a small non- rechargable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. [. . . ] The actual position of the End mark differs depending on the section that is input at the end of the song. When an Ending section is input, the End mark automatically follows the Ending data. When a section other than Ending is input, the End mark is set two measures after the final section. The End mark can be freely set to any position desired. 102 CVP-900 Recording Your Performances and Creating Songs-- Song Creator Select the Recording Options: Starting, Stopping, Punching In/Out -- Rec Mode From this display you can set up how recording is started and stopped for either Quick Recording or Multi Recording. To call up these settings, select the REC MODE display by using the [BACK][NEXT] button, after performing operation steps 1­3 on page 98. These settings determine how recording will start. Normal Overwrite recording starts when you press the SONG [START/STOP] button or when you play the keyboard with Synchro standby set to ON. First Key On Overwrite recording starts as soon as you start playing the keyboard. This setting also preserves the previous lead-in data, letting you record over the original lead-in without erasing it. Punch In At The song plays back normally up to the indicated Punch In measure (set by the [3] buttons), then starts overwrite recording at that Punch In measure. Determines the measure at which Punch In overwrite recording starts (when "PUNCH IN AT" is selected). F G H I Calls up the SONG display, from which you can save the edited data. When this is set to ON, you can use the sostenuto (center) pedal to control the punch-in and punch-out points. Determines the Punch Out measure -- the measure at which Punch In overwrite recording stops (when "PUNCH OUT AT" is selected). J 1 2 3 4 5 6 7 8 These settings determine how recording will stop as well as what happens to previously recorded data. Replace All This deletes all data following the point at which recording is stopped. Punch Out At Overwrite recording continues until the indicated Punch Out measure (set by the [6] buttons), then stops at that Punch Out measure, after which song playback continues normally. Punch Out This maintains all data following the point at which recording is stopped. When the Pedal Punch In/ Out function is set to ON, the current function assignment of the sostenuto pedal is cancelled. About Punch In/Out This feature is useful primarily for re-recording or replacing a specific section of an already recorded channel. The illustrations below indicate a variety of situations in which selected measures in an eight-measure phrase are re-recorded. REC START setting REC END setting NORMAL REPLACE ALL NORMAL PUNCH OUT NORMAL PUNCH OUT AT=006 FIRST KEY ON REPLACE ALL FIRST KEY ON PUNCH OUT FIRST KEY ON PUNCH OUT AT=006 PUNCH IN AT=003 REPLACE ALL PUNCH IN AT=003 PUNCH OUT PUNCH IN AT=003 PUNCH OUT AT=006 Original data 1 Start/start overwrite recording *1 2 3 4 5 6 7 8 Stop recording *2 *1 When measures 1 - 2 are not overwritten, recording starts from measure 3. *2 You'll have to press the [REC] button at the end of 5 measures. 1 Start/start overwrite recording *1 2 3 4 5 Stop recording *2 Deleted 1 Start/start overwrite recording *1 2 3 4 5 6 7 8 Stop overwrite recording/ play original data 1 Start/ play back original data 2 3 4 5 6 7 8 Start playing the keys/ start overwrite recording Stop recording *2 1 Start/ play back original data 2 3 4 5 Stop recording *2 Deleted Start playing the keys/ start overwrite recording 1 Start/ play back original data 2 3 4 5 6 7 8 Start playing the keys/ start overwrite recording Stop overwrite recording/ play original data 1 Start/ play back original data 2 3 4 5 6 7 8 Start overwrite recording Stop recording *2 1 Start/ play back original data 2 3 4 5 Stop recording *2 Deleted Start overwrite recording 1 Start/ play back original data 2 3 4 5 6 7 8 Previously recorded data Newly recorded data Deleted data Start overwrite recording Stop overwrite recording/ play original data 1 2 3 4 5 7 CVP-900 103 Recording Your Performances and Creating Songs-- Song Creator Editing a Recorded Song Whether you've recorded a song using Quick Recording, Multi Recording, or Step Recording, you can use the editing features to change the song data. Editing Channel-related Parameters -- Channel Calling up the operations here apply to step 4 on page 98. To call up the display shown below, use the [BACK]/[NEXT] buttons. Quantize Quantize lets you "clean up" or tighten the timing of a previously recorded channel. For example, the following musical passage has been written with exact quarter-note and eighth-note values. Even though you think you may have recorded the passage accurately, your actual performance may be slightly ahead of or behind the beat. Quantize allows you to align all the notes in a channel so that the timing is absolutely accurate to the specified note value (see below). Use this to select the desired edit operation. A F B G C H Executes the Quantize operation. After the operation is completed, this button changes to [UNDO], letting you restore the original data if you're not satisfied with the Quantize results. The Undo function only has one level; only the previous operation can be undone. D I Calls up the SONG display, from which you can save the edited data. If a value less than 100% is selected, notes will be moved toward the specified quantization beats only by the specified amount. Applying less than 100% quantization lets you preserve some of the "human" feel in the recording. E J 1 2 3 4 5 6 7 8 Selects the desired channel to be quantized. Selects the quantize size (resolution). [. . . ] 17, 200, 28230 Las Rozas (Madrid) Spain Tel: 91-201-0700 CENTRAL & SOUTH AMERICA MEXICO Yamaha de Mexico S. A. 16F 23-8 Yoido-dong, Youngdungpo-ku, Seoul, Korea Tel: 02-3770-0661 GREECE Philippe Nakas S. A. Navarinou Street 13, P. Code 10680, Athens, Greece Tel: 01-364-7111 MALAYSIA Yamaha Music Malaysia, Sdn. , Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-703-0900 BRAZIL Yamaha Musical do Brasil LTDA. [. . . ]