User manual YAMAHA AX-9

[. . . ] When moving the unit, first disconnect the power plug and the wires connected to other equipment. If these openings are obstructed, the temperature inside the cabinet will rise rapidly and eventually damage the circuits. Therefore, avoid placing objects against these openings and do not install the unit where the flow of air through the ventilation openings could be impeded. Always set the VOLUME control to "0" before starting the audio source play: increase the volume gradually to an appropriate level after the play has been started. [. . . ] Make sure that the polarity of the speaker wires is correct, that is, + and ­ markings are observed. If these wires are reversed, the sound will be unnatural and will lack bass. Do not let the bare speaker wires touch each other and do not let them touch the metal parts of this unit as this could damage this unit and/or speakers. How to Connect: Red: positive (+) Black: negative (­) q q q One or two speaker systems can be connected to this unit. If you connect only one speaker system, connect it to either the SPEAKERS A or B terminals. Use speakers with the specified impedance shown on the rear of this unit. Simply insert the Banana Plug connector into the corresponding terminal. 2 1 3 Unscrew the knob. 5mm (1/4") insulation from the speaker wires. ] Tighten the knob and secure the wire. IMPEDANCE SELECTOR switch Be sure to switch this only when the power to this unit is not on. WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/ON SWITCH IS PRESSED The IMPEDANCE SELECTOR switch may not be set to either end closely. (General model) IMPEDANCE SELECTOR SET BEFORE POWER ON A OR B:4MIN. /SPEAKER A + B:8MIN. /SPEAKER A OR B:8MIN. /SPEAKER A + B:l6MIN. /SPEAKER (Left position) If you use one pair of speakers, the impedance of each speaker must be 4 or higher. If you use two pairs of speakers, the impedance of each speaker must be 8 or higher. (Right position) If you use one pair of speakers, the impedance of each speaker must be 8 or higher. If you use two pairs of speakers, the impedance of each speaker must be 16 or higher. ABOUT THE ACCESSORY TERMINALS AC OUTLET(S) (SWITCHED) (Europe and General models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SWITCHED OUTLET Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit's STANDBY/ON switch or the provided remote control transmitter's POWER key. These outlets will supply power to any component whenever this unit is turned on. C TAPE MONITOR switch When the tape deck connected to the TAPE terminals on the rear of this unit is used for recording, you can monitor the sounds being recorded by pressing TAPE MONITOR so that TAPE MONITOR indicator lights up. D Tone controls BASS Used to increase or decrease the low frequency response. The 0 position produces flat response. E BALANCE control Adjusts the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. 8 English REMOTE CONTROL TRANSMITTER The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. If the CD player, tuner or tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this remote control transmitter will also control various functions of each component. For Control of This Unit 1 SLEEP timer key This unit is automatically turned into the standby mode one hour after this key is pressed (so that SLEEP indicator lights up). YAMAHA HIFI SYSTEM REMOTE CONTROL TRANSMITTER AUX 2 POWER key Turns the power to this unit on and turns this unit into the standby mode alternately. For Other Component Control 4 Identify the remote control transmitter keys with your component's keys. On each key function, refer to the corresponding instruction on your component's manual. DIR A DIR B REC/PAUSE PLAY MD 1 2 3 1 2 SLEEP POWER A/B TAPE ­ PRESET + A/B/C/D/E TUNER DISC PLAY CD PHONO VOLUME 1 Tape deck keys Controls tape deck. [. . . ] 105 dB Residual Noise (IHF-A Network). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ­30 dB) PHONO MM (Input 0 ohm Terminated 1 kHz) . . . . . . . . . . . . . . 60 dB CD/TUNER/TAPE/MD/AUX (Input 5. 1 k-ohms Terminated 1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 dB Tone Control Characteristics BASS: Boost/cut. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB (50 Hz) Turnover Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 Hz TREBLE: Boost/cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB (20 kHz) Turnover Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 5 kHz Power Supply [U. K. and Europe models]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230V, 50 Hz [General model] . . . . . . . . . . . . . . . . . . AC 110/120/220/240V, 50/60 Hz Power Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120W AC Outlets 3 SWITCHED OUTLETS [Europe and General models]. . . . . . . . . . . . . . . . 100W max. total Dimensions (W x H x D) . . . . . . . . . . . . . . . . . . . . . . . 280 x 118. 5 x 388. 5 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (11" x 4-11/16" x 15-5/16") Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. 1 kg (13 lbs. [. . . ]