User manual YAMAHA AX-892

[. . . ] Heat ­ The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. supply only of the type described in the operating instructions or as marked on the unit. C. The unit does not appear to operate normally or exhibits a marked change in performance; or 8 E. 16 Servicing ­ The user should not attempt to service the unit beyond those means described in the operating instructions. [. . . ] If this product is found to be the source of interference, which can be determined by turning the unit "OFF" and "ON", please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp. , U. S. A. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. We Want You Listening For A Lifetime YAMAHA and the Electronic Industries Association's Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion ­ and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association's Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. SUPPLIED ACCESSORIES After unpacking, check that the following parts are contained. q Remote Control Transmitter q Batteries (size AA, R6, UM-3) 3 CONNECTIONS q q Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other components to which connections are being made. When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, "+" to "+" and "­" to "­". Also, refer to the owner's manual for each component to be connected to this unit. <AX-1070> Compact disc player Tuner Tape deck 1 Tape deck 2 Speakers A Right Left (General model) To AC outlet Right Turntable Video cassette player, LD player, etc. By doing so, the audio signal bypasses the BASS, TREBLE, BALANCE and LOUDNESS controls, the SUBSONIC FILTER switch and the PRE OUT/MAIN IN terminals, eliminating any alterations to the audio signal. Setting the PHONO switch Select either MM or MC position depending on your PHONO cartridge, Moving Magnet or Moving Coil type. However, if you use a high output MC cartridge, select MM position. PHONO MC PURE DIRECT MM Setting the SUBSONIC FILTER switch If you set this switch to "ON" position, undesirable ultra-lowfrequency signals caused by turntable rumble or warped records can be cut out without losing sound quality. Setting the MODE switch <For AX-1070 only> This switch can be used for switching between stereo and monaural operation. Normally this switch should be set to the STEREO position. MODE MONO SUBSONIC FILTER ON OFF STEREO When you listen with headphones Connect the headphones to the PHONES jack. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position. PHONES 11 REMOTE CONTROL TRANSMITTER The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the CD player, tuner, turntable, equalizer, and tape deck connected to this unit are YAMAHA components, then this remote control transmitter will also control various functions of each component. KEY FUNCTIONS For Control of This Unit Turns the power on/off. Selects input source. When pressed, mutes the volume level. While muting, the indicator on the VOLUME control flashes on and off continuously. Turns the volume level up/down. For Other Component Control Identify the remote control transmitter keys with your component's keys. On each key function, refer to the corresponding instruction on your component's manual. A/B/C/D/E: Selects the page (A ­ E) of preset station buttons. Controls compact disc player. * DISC SKIP is applicable only to compact disc changer. Controls tape deck. * DIR A, B and DECK A/B are applicable only to double cassette tape deck. [. . . ] The batteries of this remote control transmitter are too weak. Replace the batteries with new ones. 14 SPECIFICATIONS Minimum RMS Output Power per Channel Output Level/Impedance English <AX-1070> 8 ohms, 20 Hz to 20 kHz, 0. 01% THD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145W+145W 6 ohms, 20 Hz to 20 kHz, 0. 02% THD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185W+185W <AX-1070> REC OUT . . . . . . . . . . . . . . . . . . . . 150 mV/2. 2 k-ohms PRE OUT. . . . . . . . . . . . . . . . . . . . . . . . . . 1. 0V/1. 8 k-ohms <AX-892> REC OUT . . . . . . . . . . . . . . . . . . . . 150 mV/2. 2 k-ohms PRE OUT. . . . . . . . . . . . . . . . . . . . . . . . . . 1. 0V/1. 6 k-ohms Maximum Voltage Output Channel Separation (Vol. ­30 dB) PHONO MM/MC (Input Shorted 1 kHz/10 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . 70 dB/55 dB CD/TUNER/TAPE/AUX (Input 5. 1 k-ohms Terminated 1 kHz/10 kHz) . . . . . . 65 dB/50 dB Tone Control Characteristics BASS: Boost/cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB (20 Hz) Turnover Frequency <AX-1070>. . . . . . . . . . . . . . . . . . . . . . . . . . . 200, 400 Hz <AX-892>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 Hz TREBLE: Boost/cut. . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB (20 kHz) Turnover Frequency <AX-1070>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. 5, 5 kHz <AX-892>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 5 kHz Filter Characteristics SUBSONIC FILTER . . . . . . . . . 15 Hz, ­18 dB/oct Continuous Loudness Control (Level related equalization) Attenuation <AX-1070> . . . . . . . . . . . . . . . . . . . . . . . . ­40 dB (1 kHz) <AX-892> . . . . . . . . . . . . . . . . . . . . . . . . . . ­30 dB (1 kHz) Audio Muting <AX-1070 only>. . . . . . . . . . . . . ­20 dB Gain Tracking Error (0 to ­60 dB) . . . . . . . . . . . . 2 dB <AX-892> 8 ohms, 20 Hz to 20 kHz, 0. 015% THD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110W+110W 6 ohms, 20 Hz to 20 kHz, 0. 03% THD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130W+130W Dynamic Power per Channel (by IHF Dynamic Headroom measuring method) <AX-1070> 20 Hz to 20 kHz, 0. 02% THD . . . . . . . . . . . . . . 6. 5V <AX-892> 20 Hz to 20 kHz, 0. 01% THD . . . . . . . . . . . . . . 1. 4V Headphone Jack Rated Output/ Impedance Output Level (8 ohms, 1 kHz, 0. 015% THD) <AX-1070> 8/6/4/2 ohms. . . . . . . . . . . . . . . . . 220/290/360/460W <AX-892> 8/6/4/2 ohms. . . . . . . . . . . . . . . . . 150/200/250/330W DIN Standard Output Power per Channel [Europe model only] <AX-1070>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 05V <AX-892>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 5V Impedance <AX-1070> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 ohms <AX-892> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470 ohms Frequency Response (20 Hz to 20 kHz) CD/TUNER/TAPE/AUX . . . . . . . . . . . . . . . . . . . . 0±0. 5 dB MAIN IN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0±0. 5 dB RIAA Equalization Deviation (20 Hz to 20 kHz) PHONO MM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0. 3 dB PHONO MC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0. 5 dB Total Harmonic Distortion (20 Hz to 20 kHz) <AX-1070> (4 ohms, 1 kHz, 0. 7% THD) . . . . . . . . . . . . . . 250W <AX-892> (4 ohms, 1 kHz, 0. 7% THD) . . . . . . . . . . . . . . 185W Dynamic Headroom [General model only] <AX-1070> 8/6 ohms . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 81 dB/1. 95 dB <AX-892> 8/6 ohms . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 35 dB/0. 97 dB IEC Power (8 ohms, 1 kHz, 0. 01% THD) [Europe model only] <AX-1070> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170W <AX-892> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125W Power Band Width <AX-1070> PHONO MM to REC OUT (3V) . . . . . . 0. 003% PHONO MC to REC OUT (3V). . . . . . . 0. 007% CD/TUNER/TAPE/AUX to PRE OUT (1V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 004% CD/TUNER/TAPE/AUX to SP OUT (72. 5W/8 ohms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 007% MAIN IN to SP OUT (72. 5W/8 ohms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 005% Power Supply [Australia and U. K. models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 240V, 50 Hz [Europe model]. . . . . . . . . . . . . . . . . . AC 230V, 50 Hz [General model] . . . . . . . . . . . . . . . . AC 110/120/220/240V, 50/60 Hz Power Consumption <AX-1070> 8 ohms, 72. 5W, 0. 03% THD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Hz to 50 kHz <AX-892> PHONO MM to REC OUT (3V) . . . . . . 0. 003% PHONO MC to REC OUT (3V). . . . . . . 0. 007% CD/TUNER/TAPE/AUX to PRE OUT (1V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 005% CD/TUNER/TAPE/AUX to SP OUT (55W/8 ohms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 008% MAIN IN to SP OUT (55W/8 ohms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 006% Signal-to-Noise Ratio (IHF-A Network) PHONO MM (5 mV Input Shorted) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 dB PHONO MC (500 µV Input Shorted) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]