User manual YAMAHA AX-392

[. . . ] customers If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet. 4. Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. If these openings are obstructed, the temperature inside the cabinet will rise rapidly. [. . . ] If you connect only one speaker system, connect it to either the SPEAKERS A or B terminals. Use speakers with the specified impedance shown on the rear of this unit. <China and General models only> Banana Plug connections are also possible. Simply insert the Banana Plug connector into the corresponding terminal. 2 1 3 Unscrew the knob. 5mm (1/4") insulation from the speaker wires. ] Tighten the knob and secure the wire. IMPEDANCE SELECTOR switch Be sure to switch this only when the power to this unit is not on. WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/ON SWITCH IS PRESSED; The IMPEDANCE SELECTOR switch may not be set to either end closely. If so, set the switch to either end closely. IMPEDANCE SELECTOR SET BEFORE POWER ON A OR B : 4MIN. /SPEAKER (Upper position) If you use one pair of speakers, the impedance of each speaker must be 4 or higher. If you use two pairs of speakers, the impedance of each speaker must be 8 or higher. (Lower position) If you use one pair of speakers, the impedance of each speaker must be 6 or higher. If you use two pairs of speakers, the impedance of each speaker must be 12 or higher. ABOUT THE ACCESSORY TERMINALS AC OUTLET(S) (SWITCHED) (Europe, China and General models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SWITCHED OUTLET Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit's STANDBY/ON switch or the provided remote control transmitter's POWER key. These outlets will supply power to any component whenever this unit is turned on. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position. PHONES 6 TAPE MONITOR indicator Lights up while the TAPE MONITOR switch is on. * When the tape deck (TAPE) is selected as the input source, this indicator will not light up even if the TAPE MONITOR switch is on. 8 English B SPEAKERS switches Set the switch A or B (or both A and B) for the speaker system (connected to this unit) you will use to the ON position. Set the switch for the speaker system you will not use to the OFF position. C Tone controls BASS Used to increase or decrease the low frequency response. The 0 position produces flat response. D BALANCE control Adjusts the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. E Continuously variable LOUDNESS control Used to compensate for the human ears' loss of sensitivity to high and low-frequency ranges at low volume. F Control door See below for how to open and close the control door. Open/close the control door When it is not necessary to operate controls inside the control door, close the door. To open the door To close the door 1 2 9 REMOTE CONTROL TRANSMITTER The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. [. . . ] 100 µV Channel Separation CD/TUNER/AUX/MD/TAPE (Input 5. 1 k-ohms Terminated 1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 dB Tone Control Characteristics BASS: Boost/cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB (20 Hz) Turnover Frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 Hz TREBLE: Boost/cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB (20 kHz) Turnover Frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 5 kHz Continuously variable LOUDNESS Control (Level related equalization) Attenuation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . and Europe models]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230V, 50 Hz [China and General models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 110/120/220/240V, 60/50 Hz Power Consumption [U. K. and Europe models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150W (In the standby mode: 1. 2W) [China and General models]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150W (In the standby mode: 1. 8W) AC Outlets 3 SWITCHED OUTLETS [Europe, China and General models] . . . . . . . 100W max. total Dimensions (W x H x D) . . . . . . . . . . . . . . . . . . . . . . . . . . 435 x 151 x 309. 3 mm (17-1/8" x 5-15/16" x 12-3/16") Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. 6 kg (16 lbs. [. . . ]