User manual YAMAHA AUDIOGRAM6

[. . . ] EN DE FR ES RU JA Español Français Deutsch Owner's Manual Bedienungsanleitung Mode d'emploi Manual de instrucciones English USB AUDIO INTERFACE COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Address : Telephone : Type of Equipment : Model Name : Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. 90620 714-522-9011 COMPUTER RECORDING SYSTEM AUDIOGRAM 6 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. [. . . ] Select MIC ( ) if a microphone is connected, or INST ( ) if an electric guitar or bass is connected. NOTE If a device is not connected to the MIC/ INST jack, set this switch to MIC ( ). Otherwise noise may occur. You can directly connect an electric guitar or bass without the need for a separate DI (Direct Injection) box or amp simulator. 2 LINE Input Jacks (L (MONO)/R) These inputs are intended mainly for use with instruments and equipment having stereo outputs, such as a synthesizer or CD player. If you connect to the L (MONO) jack only, the AUDIOGRAM will recognize the signal as monaural and will send the identical signal to both the L and R jacks. Phone-type 6 GAIN Control Adjusts the input signal level. To achieve the best balance between S/N ratio and dynamic range, adjust the level so that the input channel PEAK indicator 9 lights only occasionally and briefly on the highest input transients. AUDIOGRAM 6 Owner's Manual 15 Controls and Functions 7 COMP Control Adjusts the amount of compression applied to the channel. As the knob is turned to the right, the interface automatically raises the compression ratio while adjusting the output gain accordingly. The result is smoother, more even dynamics because louder signals are attenuated while the overall level is boosted. NOTE Avoid setting the compression too high, as the higher average output level that results may lead to feedback. CAUTION 8 MONO/STEREO Switch This switch allows channels 1 and 2 to be used either as separate mono channels or as a stereo pair. When set to MONO ( ), channels 1 and 2 function as independent mono channels feeding both the L and R STE), input REO OUT jacks 3. When set to STEREO ( channels 1 and 2 function as a stereo pair: the channel 1 signal feeds the L STEREO OUT jack and the channel 2 signal feeds the R STEREO OUT jack. · Be sure to leave this switch off ( ) if you do not need phantom power. · When turning the switch on, be sure that only a condenser microphone is connected to the channel 1 MIC/INST input jack. This precaution does not apply to balanced dynamic microphones or instruments with the phone jack, however, as these will not be affected by phantom power. · To prevent damage to speakers, be sure to turn off power amplifiers (or powered speakers) before turning this switch on or off. We also recommend that you set the MASTER LEVEL control to the minimum position. Neglect of these precautions may result in large noise bursts that may damage your equipment, your ears, or both. C Level Indicators These indicators show signal levels prior to the MASTER LEVEL control E. The SIGNAL LED lights when a signal is present, and the PEAK LED lights when the signal reaches or exceeds clipping level. Adjust the input channel LEVEL controls 0 so that the PEAK LEDs flash only briefly on occasional high-level peaks or not at all. 9 PEAK Indicators The PEAK indicators light when the channel signal reaches or exceeds clipping level. Note that signal levels as indicated by the PEAK indicators are affected by both the GAIN and LEVEL controls. If a PEAK indicator lights, adjust the GAIN 6 and COMP 7 controls to lower the level so that the indicator goes out. D E DAW Control Adjusts the level of the signal received from Cubase AI sent to the AUDIOGRAM STEREO OUT jacks 3. 0 LEVEL Controls Adjusts the level of the channel signal. Use these controls to adjust the balance between the various channels. MASTER LEVEL Control Adjusts the signal level sent to the STEREO OUT jacks 3. This allows you to adjust the overall volume without changing the relative volume balance among the channels. A POWER Indicator This indicator lights when power is applied to the AUDIOGRAM interface via the USB cable (supplied) that connects it to the computer. F USB Connector Connects the AUDIOGRAM interface to a USB port on your computer via the supplied USB cable. In addition to transferring audio data between the AUDIOGRAM interface and the computer, the USB cable supplies power from the computer to the AUDIOGRAM interface. When connecting or disconnecting the USB cable be sure to turn the DAW control and the MASTER LEVEL control all the way down. B PHANTOM +48V (CH1) Switch/Indicator (only for channel 1) This switch toggles phantom power on and off. [. . . ] No amendment or revision of this Agreement will be binding unless in writing and signed by a fully authorized representative of Yamaha. AUDIOGRAM 6 Owner's Manual 107 For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. POLAND Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. [. . . ]