User manual YAMAHA 01V96

[. . . ] Owner's Manual Keep This Manual For Future Reference. E FCC INFORMATION (U. S. A. ) 1. This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. [. . . ] The I/O configuration of the effect program is displayed below this parameter. C button Move the cursor to this parameter, then press [ENTER] to display the Library page for the selected effects processor. button Move the cursor to this button, then press [ENTER] to display the Patch | Effect page, which enables you to assign signals to the inputs and outputs of Effects processors 1­4. This parameter knob enables you to set the balance between wet and dry signals. Turn on the BYPASS button to bypass the currently-selected effects processor. D E MIX BALANCE 01V96--Owner's Manual 158 Chapter 14--Internal Effects F TEMPO This section enables you to set the tempo and interval of the selected effects, and displays certain parameters only when certain effect types are selected. Use the parameter control on the left side of this section to adjust the value between 25BPM and 300BPM. When the MIDI CLK button is on, the 01V96 updates the TEMPO data (BPM) based on the MIDI Clock information received at the MIDI IN port. You can also specify the tempo by moving the cursor to the TAP TEMPO button and double-clicking the [ENTER] button. The 01V96 calculates the tempo based on the time interval between your two taps (clicks) on the [ENTER] button. Tip: If the Freeze effect is selected, the TEMPO section displays the record and playback buttons for using the effect, the recording data condition, and a progress bar that indicates the current status. G Meters These meters indicate the input or output levels of the currently-selected effects processor. Select the IN button or OUT button to display the input levels or output levels respectively. Tip: You can also view the input and output levels of the effects processors on the Meter | Effect 1­4 pages (see page 34). Move the cursor to a parameter you wish to change, and rotate the Parameter wheel or press the [INC]/[DEC] buttons to adjust the setting. You can store the edited settings as a new program in the Effects library (see page 175). To change the effects type, recall a program that uses the desired effects type from the Effects library. 01V96--Owner's Manual About Plug-Ins 159 About Plug-Ins If you installed a mini-YGDAI card that supports the Effects function into Slot, you can use plug-in effects in addition to the internal effects processors. You can patch Bus signals or channel insert outs to the plug-in input. The plug-in output can be patched to Input Channels or channel insert ins. To use the plug-in effects, press the [EFFECT] button repeatedly until the Effect | P-In Edit page appears. For details on using plug-ins, refer to the owner's manual that came with the plug-in card. As of February 2003, the 01V96 supports the following plug-in cards. Visit the Yamaha web site (http://www. yamahaproaudio. com/) for the latest information on compatible plug-in cards. · Waves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Y56K 14 Internal Effects 01V96--Owner's Manual 160 Chapter 14--Internal Effects 01V96--Owner's Manual Scene Memories 161 15 Scene Memories This chapter describes Scene memories, which store 01V96 mix and effects settings. About Scene Memories Scene memories enable you to store a snapshot of 01V96 channel mix settings and internal effects processor settings as a "Scene" in a special memory area. There are 99 Scene memories, and you can recall any Scene using the display pages or the controls on the top panel. Tip: · You can recall Scenes by transmitting Program Changes from external MIDI devices (see page 215). [. . . ] Input [+24dBu] [+18dBu] CASCADE IN CASCADE OUT Digital Clipping Level Max. Output [+24dBu] +24 +20 +10 +4 0 ­10 ­20 ­30 [+4dBu] Nominal Input GAIN MIN. , PAD ON Nominal Output [+4dBu] [-2dBu] STEREO OUT OMNI OUT MONITOR OUT Max. Input [-40dBu] ­40 ­50 Nominal [-60dBu] Input GAIN MAX. , PAD OFF ­60 ­70 ­80 ­90 ­100 ­110 ­120 ­130 ­140 ­150 ­160 DSP Noise Floor ­170 ­180 ­190 [0dBu = 0. 775Vrms] [0dBFS = Full Scale] For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. [. . . ]