User manual YAMAHA 01V

[. . . ] L) NBA V (U dB ­10 ON OFF 48V M+ NTO PHA 15 13 16 14 L R T OU IN 2TR NES PHO OR NIT MOR IN 2T 6 15/1 IN 2TR 10 0 10 0 EL LEV B 26d B 26d B 26d B 26d B 26d ­60 ­34 ­60 ­34 ­60 ­34 ­20 +10 GAIN ­16 GAIN +10 ­20 +10 GAIN OR NIT MO UT O EL LEV NES PHO 13/1 4 15/1 6 11 Owner's10Manual ­60 ­34 ­16 GAIN +10 ­60 ­34 ­16 GAIN +10 ­16 GAIN +10 12 IN GA ­60 ­34 ­16 GAIN +10 9 D AL IGIT IN MIX GC O L NSO E R EO TER LS P CLI ­3 ­6 ­9 8 H HIG EQ PAN HI-M ID 7 F PAN F G MID LOLOW G L NNE CHA ED ECT SEL ­12 ­15 ­18 ­24 ­30 ­36 ­42 ­48 2 URN RET 1 12 11 10 9 EL SEL SEL 6 15/1 4 13/1 SEL SEL EO TERTER S S MA L SE 2 RN ETU 1R SEL SEL S O SOL O SOL O SOL E ON ON FCC INFORMATION (U. S. A. ) 1. This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. [. . . ] With the REC MODE is set to INPUT, recording starts automatically when an input signal exceeds the TRG LVL. (PLAY) switch, and then press the With the PLY MODE is set to INPUT, playback starts automatically when an input signal exceeds the TRG LVL. Use the PLY MODE parameters to set the type of playback, and the START, END, and LOOP parameters to edit the sample. Be aware that samples are lost when another type of effect is recalled or the 01V is turned off. 01V--Owner's Manual Effects Block Diagram 159 Effects Block Diagram BUS AUX EFF ST 1234 1234 12 LR Effect send 1 master fader ON Effect send 2 master fader ON Meter Meter 4-Band PEQ Internal Effect 1 4-Band PEQ ON EFF RTN 1 Rotary PAN* AUX1 AUX2 AUX3 AUX4 EFF2 AUX/EFF PRE/POST Meter Meter 4-Band PEQ Internal Effect 2 4-Band PEQ ON EFF RTN 2 Rotary PAN* AUX1 AUX2 AUX3 AUX4 EFF1 AUX/EFF PRE/POST *PAN: INDIVIDUAL/GANG/INV. GANG 01V--Owner's Manual Dynamics Processors 161 Dynamics Processors 13 In this chapter. . . About the Dynamics Processors . 162 163 164 166 167 173 174 175 176 177 01V--Owner's Manual 162 Chapter 13--Dynamics Processors About the Dynamics Processors Input channels 1 through 16, the aux sends, and the stereo output all feature powerful dynamics processors, offering compressor, limiter, gate, ducker, and compander functions. See the "Block Diagram" on page 24 for the exact location of each dynamics processor. Input channel processors can be self triggering (i. e. , the signal being processed is used as the trigger signal), or triggered by a signal from another input channel. Dynamics settings are stored as programs in the dynamics library, which contains 40 preset programs and 40 user programs. Use the [DYNAMICS] button to locate this page. The name of the type of dynamics processor appears in the middle of the page next the dynamics curve. Below these are the dynamics parameters, the number of which vary depending on the type of processor selected. The GR meter indicates the amount of gain reduction being applied to the selected channel. Next to this are level meters for the selected channel and its neighbor. 01V--Owner's Manual Preset Dynamics Programs 163 Preset Dynamics Programs The following table lists the preset dynamics programs. See "Preset Dynamics Program Settings" on page 177 for detailed parameter information. No. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 Comp Gate Expand Ducking Compander(H) Compander(S) A. Dr. BD A. Dr. BD A. Dr. BD A. Dr. SN A. Dr. SN A. Dr. SN A. Dr. SN A. Dr. Tom A. Dr. OverTop E. B. Finger E. B. Slap Syn. Bass Piano1 Piano2 Title GATE EXPAND DUCKING COMPAND-H COMPAND-S COMP GATE COMPAND-H COMP EXPAND GATE COMPAND-S EXPAND COMPAND-S COMP COMP COMP COMP COMP Type COMP No. 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Title E. Guitar A. Guitar Strings1 Strings2 Strings3 BrassSection Syn. Pad SamplingPerc Sampling BD Sampling SN Hip Comp Solo Vocal1 Solo Vocal2 Chorus Click Erase Announcer Limiter1 Limiter2 Total Comp1 Total Comp2 Type COMP COMP COMP COMP COMP COMP COMP COMPAND-S COMP COMP COMPAND-S COMP COMP COMP EXPAND COMPAND-H COMPAND-S COMP COMP COMP 01V--Owner's Manual 164 Chapter 13--Dynamics Processors Using the Dynamics Processors Input channels 1 through 16, the aux sends, and the stereo output all feature dynamics processors. To recall a program from the dynamics library, see "Recalling Dynamics Programs" on page 175. To edit a dynamics processor, see"Editing the Dynamics Processors" on page 166. For Input Channels 1­16 1. Use the [DYNAMICS] button to locate DYNAMICS page 1, as shown below. 3. The ON/OFF switch appears highlighted when the dynamics processor is on. While DYNAMICS page 1 is displayed, the [ENTER] button turns the dynamics processor on or off regardless of the cursor position. Use the cursor buttons to select the parameters, and the PARAMETER wheel or [­1/DEC] and [+1/INC] buttons to set them. [. . . ] Pink noise--A type of random noise that contains an equal amount of energy per octave. For example, the bands 100­200, 800­1600, and 3000­6000 all contain the same amount of energy. White noise, on the other hand, has an equal amount of energy per frequency band. Aux sends are often configured as post-fader sends, which means the aux send signal is sourced after the channel fader. [. . . ]