User manual XYRON PRO1250

[. . . ] Always test before use ­ may not be compatible with some surfaces. The system is designed to be used with one of the following replacement cartridges: DL1201-150 SL1201-150 LAT1201-100 LAT1206-100 AT1201-100 AT1202-100 AT1205-100 AT1206-100 Two-Sided Lamination ­ General Use ­ 150' Single-Sided Lamination ­ General Use ­ 150' One Side Laminate / One Side Adhesive Application ­ High Tack ­ 100' One Side Laminate / One Side Adhesive Application ­ Repositionable ­ 100' Adhesive Adhesive Adhesive Adhesive Application Application Application Application ­ ­ ­ ­ High Tack ­ 100' Low Tack ­ 100' Acid Free ­ 100' Repositionable ­ 100' Consult your authorized Xyron dealer for information on other supplies. Please follow the attached directions carefully. EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 Understanding the Xyron Pro1250's Parts & Functions Input Tray Used to guide items into the machine. [. . . ] Close top cover. 7 Slide input tray back into machine completely. 8 If You Have Additional Questions, Contact the Xyron Technical Hotline: 800-793-3523 in the U. S. A. and +45-7594-5866 in Europe E-mail address in the U. S. A. : comments@xyron. com E-mail address in Europe: europe@xyron. com Also, check out our website at www. xyron. com EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 Basic Operation Before inserting your document, turn crank handle clockwise one revolution to ensure film is wrinkle-free. Extend the document underneath the paddle on the feed tray and completely into the cartridge opening until it touches the film/adhesive. 1 Gently guide the document forward while turning the crank handle clockwise. TIP: To save a later trimming operation, trim off any excess material on the leading edge of the output (with cut blade) before advancing completely through the dispenser. 2 Trim to desired length using the cut blade at the roller exit. Apply downward pressure on the orange blade holder and slide to the left or right. When applying adhesive, remove the protective clear film on top to eliminate excess adhesive from around your item. Remove white liner when you're ready to adhere to your item. 3 EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 Basic Operation How to Do Two-Sided Lamination Verify that a front and back lamination cartridge (designated DL1200 series on the cartridge label) is installed. How to Do Single-Sided Lamination Verify that a front-side lamination cartridge (designated SL1200 series on the cartridge label) is installed. How to Apply Adhesive to One Side of an Item Verify that an adhesive transfer cartridge (designated AT1200 series on the cartridge label) is installed. Place the side of the document to which you want adhesive applied face down on the tray. When ready, peel away the white paper liner from the backside of document and mount your item. How to Do Front-Side Lamination with Back-Side Adhesive Application Verify that a laminating/back side adhesive cartridge (designated LAT1200 series on the cartridge label) is installed. Place the side of the document to which you want adhesive applied face down on the tray. Peel away the white paper liner from the backside of document prior to mounting. TIP: To save a later trimming operation, turn the crank to advance the document until the leading edge is aligned with the upper blade bar supporting the cut blade. Continue to crank document through machine and trim when finished. Refill Cartridges Product No. [. . . ] Output tray not seated. Document wrinkles or exits machine crooked. Adhesive build-up on front edge of input tray or output tray is not completely pushed forward and down. *Use Cleaning Kit Xyron #990 for adhesive removal. THE PURCHASE OR ACQUISITION OF THIS PRODUCT DOES NOT CONFER THE RIGHT OR LICENSE TO USE THE MACHINE AND CARTRIDGES IN THE RETROREFLECTIVE FIELD OR TO MAKE OR SELL MACHINES OR CARTRIDGES FOR USE IN THE RETROREFLECTIVE FIELD. warrants that the Xyron Pro1250 is free from defects in material and workmanship for a period of one (1) year from the date of purchase. will repair or replace a defective product or part without charge provided it is returned to the address below, freight prepaid with proof of purchase. [. . . ]