User manual XINDAK DAC-8

[. . . ] • So that a minimum distance of 20 mm is maintained between the installation cavity and the cabinet underneath. 12 40 The thickness of the supporting surface should be taken into account when choosing screws for the fixing hooks: • 30 mm thick: 17. 55 mm screws Separate the wires and connect them in accordance with the instructions given in the following table and diagrams: Voltage and mains frequency 400V - 2+N ~ 50 Hz 230V 3 ~ 50Hz Electrical cable Wire connection : yellow/green; N: the two blue wires together L1: black L2: brown : yellow/green; N1: blue 400V - 2+2N ~ ı 50 Hz N2: blue L1: black L2: brown GB Fix the hob as follows: 1. Use short flat-bottomed screws to fix the 4 alignment springs in the holes provided at the central point of each side of the hob. [. . . ] _ COOKING ZONE SELECTOR button is used to select the required cooking zone. _ POWER indicator provides a visual display for the current heat level. _ INCREASE POWER button switches on the hotplate and controls the power (see Start-up and use). • REDUCE POWER button controls the power and switches off the hotplate (see Start-up and use). 14 Start-up and use  The glue applied on the gaskets leaves traces of grease on the glass. Before using the appliance, we recommend you remove these with a special nonabrasive cleaning product. During the first few hours of use there may be a smell of rubber which will disappear very quickly.  A few seconds after the hob is connected to the Switching off the cooking zones • Press the button: the power of the cooking zone will progressively decrease until it is switched off. This immediately returns the power setting to 0 and the cooking zone switches off. Switching on the hob To switch the hob on, press and hold the for approximately one second. Button Programming the cooking time  All the cooking zones may be programmed for a length of time between 1 and 99 minutes. • Always use pans with a diameter that is large enough to cover the hotplate fully, in order to use all the available heat. • Make sure that the base of the cookware is always dry and clean, to fully utilise and extend the life of both the cooking zones and cookware. • Avoid using the same cookware that has been used on gas burners: the heat concentration on gas burners may distort the base of the pan, causing it not to adhere correctly. Power level 1-2 3-4 5 6-7-8 9 Maximum operating time in hours 6 5 4 1, 5 1, 5 16 Buzzer This can also indicate several irregularities: • An object (a pan, cutlery, etc. To unlock it press the button, the settings will have been maintained. If the cause of the problem is not removed, the buzzer will keep sounding and the hob will switch off. GB 17 Precautions and tips GB  This appliance has been designed and manufactured in compliance with international safety standards. The following warnings are provided for safety reasons and must be read carefully. This appliance conforms to the following European Economic Community directives: - 73/23/EEC dated 19/02/73 (Low Voltage) and subsequent amendments; - 89/336/EEC dated 03/05/89 (Electromagnetic Compatibility) and subsequent amendments; - 93/68/EEC dated 22/07/93 and subsequent amendments. • • • General safety  Make sure that the air inlet behind the fan grille is never obstructed. The built-in hob should, in fact, be provided with suitable ventilation for the cooling of the electronic components used in the appliance. [. . . ] Remove spills as soon as possible, without waiting for the appliance to cool, to avoid residues forming crusty deposits. You can obtain excellent results by using a rust-proof steel wire sponge - specifically designed for glass ceramic surfaces - soaked in soapy water.  The scraper provided is sharp: be careful when the appliance breaks down, contact a Service Centre. • If any plastic or sugary substances are accidentally melted on the hob, remove them immediately with the scraper, while the surface is still hot. [. . . ]