User manual WHITES ELECTRONICS SM

[. . . ] Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. For customers in the United States This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed 12 Using the display 13 Locating a specific track 14 Playing tracks repeatedly (Repeat Play) 15 Creating your own program (Program Play) 19 Setting the clock 20 Waking up to music 22 Falling asleep to music The player turns on automatically and starts playing the CD. [. . . ] To locate aspecifictrackdirectly a point while listening to the sound Press the number button of the track + (forward) or = (backward) while playing and hold down until you find the point + (forward) or = (backward) in pause and hold down until you find the point You can play tracks repeatedly in normal, shuffle or program play modes (see page 15). Tip Press and hold LOOP on the remote during play to repeat a selected part of a CD. MONO/ST ISS on the player) until the repeat mode you want appears in the display. To repeat a single track allthetracks tracks in random order programed tracks Select REP 1 REP ALL SHUF REP PGM REP Do either of the following to start repeat play: · When you've selected REP1, select the track by pressing the number button (pressing = or + then ^ on the player). When you're selected PGM REP, program tracks (see step 3 on page 15), then press ( (^ on the player). To cancel Repeat Play Press MODE until "REP" disappears from the display. ENTER MEMORY for the tracks you want to program in the order you want. You can play the same program again, since the program is saved until you turn off the power or open the CD compartment. After you've created the program, insert a blank tape and press r to start recording. Press the number buttons for the tracks you want to program in the order you want. To cancel Program Play Press MODE until "PGM" disappears from the display. Falling asleep to music You can set the player to turn off automatically after 10, 20, 30, 60, 90, and 120 minutes, allowing you to fall asleep while listening to music. When you are playing radio or CD, make sure that ( of the tape player is not depressed. Set the waking up timer first (see page 20), turn on the power, and then set the sleeping timer. Note When you are playing a tape using this function: If the tape length of one side is longer than the set time, the player will not go off until the tape reaches the end. Each time you press the button, the indication changes as follows: "60" n "90" n "120" n no indication n "10" n "20" n "30. If you connect any other speakers or equipment, a malfunction may occur. Replacing batteries With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. Choose ROCK VOCAL LIVE POP OFF To get powerful, clean sounds, emphasizing low and high range audio the presence of vocals, stressing middle range audio percussive sounds, emphasizing bass audio light, bright sounds emphasizing high and middle range audio the whole dynamic range for music such as classical music To return to normal sound, press the button again. As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing. Should any solid object or liquid fall into the player, unplug the player, and have it checked by qualified personnel before operating it any further. [. . . ] The use of a cassette with more than 90 minutes of play time is not recommended except for long, continuous recording or playback. ⷠMake sure the function you want to use appears in the display. To make the best possible recording, however, we recommend that you clean all surfaces over which tape travels before each recording. Demagnetizing the tape heads After 20 to 30 hours of use, enough residual magnetism will have built up on the tape heads to begin to cause loss of high frequency sound and hiss. [. . . ]