User manual WHITES ELECTRONICS OREMASTER 500EC

[. . . ] A 60 83 168 100 120 121 148 B Connecting the water inlet hose • To a suitable cold water connection point: before attaching the hose, run the water until it is perfectly clear so that any impurities that may be present in the water do not clog the appliance; after performing this operation, screw the inlet hose tightly onto a tap with a ¾ gas threaded connection. €¢ To a suitable hot water connection point: your dishwasher may be provided with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C. Screw the hose to the tap as described for connection to a cold water supply. If the inlet hose is not long enough, contact a specialist store or an authorised technician (see Assistance ). [. . . ] Switch off the appliance by pressing the STANDBY button and turn off the water tap. Open the door and wait for a few minutes before removing the crockery, in order to avoid burns. To obtain the best results from each washing and drying cycle, powder detergent, rinse aid liquid and salt should be used. Pour in the detergent after consulting the Wash cycle table: • for powder detergent use compartments A and B • for tablets, when the cycle requires 1 tablet, place it in compartment A and close the C cover; when it requires 2, place the second tablet at the bottom of the appliance. Remove detergent residues from the edges of the compartment and close the cover until it clicks. D A B Demo* If dON appears on the display, this means that the appliance is in demonstration mode. To deactivate it, press the START/ RESET and STAND/BY buttons simultaneously: dOF should appear on the display. Washing options Delayed start It is possible to delay the start time of the cycle for a period of time between 1 and 24 hours. Press the DELAYED START button: every time the button is pressed, the time selected appears on the display and the delayed start indicator light illuminates. Select the wash cycle and press the START/RESET button: after the beep sounds, the timer begins counting down. Once this time is up, the indicator light switches off and the wash cycle begins. €¢ when the LOW RINSE AID* indicator light on the panel flashes; 1. Open the dispenser by turning the lid (G) in an H anticlockwise direction. Pour in the rinse aid, making sure it does not overflow from the dispenser. Adjusting the amount of salt* It is possible to adjust the amount of salt used according to the hardness of the water in your area (this information is available from your local water board). Turn the arrow on the neck of the dispenser (see figure) towards the + or symbols, using the table below as a guide. 9 Autonomy (cycles/2 kg) / 60 40 25 Adjusting the amount of rinse aid If you are not completely satisfied with the drying results, you may adjust the quantity of rinse aid used. Use a screwdriver to turn the dosage adjuster to one of the 6 pre-set positions (the default position is set to 4): • if there are streaks on the crockery, set the adjuster to a lower number (1-3). €¢ if drops of water remain on the crockery or there are limescale marks present after the cycle has finished, set the adjuster to a higher number (4-6). If you are using multi-functional tablets and you wish to further improve the drying performance of the appliance, fill the dispenser and set the dosage adjuster to 2. 0 - 10 10 – 25 25 – 50 > 50 The default setting of the water softening system is +. - If using multi-functional tablets fill the salt dispenser and set the adjuster to -; if the hardness of the water is greater than 60°fH, set it to +. [. . . ] €¢ Select a wash cycle that is suited to the type of crockery and to the soil level of the crockery using the Wash cycle table: - for dishes with a normal soil level, use the Eco wash cycle, which guarantees low energy and water consumption levels. - if the load is smaller than usual activate the Half load option (see Start-up and use). €¢ If your electricity supply contract gives details of electricity saving time bands, run wash cycles during the periods when a lower tariff is applied. The Delayed start* button (see Start-up and use) helps you organise the wash cycles accordingly. [. . . ]