User manual WHITES ELECTRONICS 5000 D S3

[. . . ] €¢ To a suitable hot water connection point: your dishwasher may be provided with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C. Screw the hose to the tap as described for connection to a cold water supply.  If the inlet hose is not long enough, contact a specialist store or an authorised technician (see Assistance ).  The water pressure must be within the values indicated in the Technical data table (see below). [. . . ] Modifying a wash cycle in progress If a mistake was made during the wash cycle selection process it is possible to change the cycle, provided that it has only just begun: open the door, taking care to avoid the escaping steam, and press the WASH CYCLE SELECT button, holding it for 4 seconds. After one long beep and three short beeps, the WASH CYCLE indicator light will switch off: select the new wash cycle and start the programme by shutting the door. Adding extra crockery Open the door, taking care to avoid the escaping steam, and place the crockery inside the dishwasher. Close the door: the cycle starts from the point at which it was interrupted. Accidental interruptions If the door is opened during the wash cycle, or if there is a power cut, the cycle stops. It starts again from the point at which it was interrupted once the door has been shut or the electricity supply is restored. €¢ for powder detergent use compartments A and B • for tablets, use compartment A and the bottom of the appliance, i. When the cycle requires 1 tablet, place it in compartment A and close the cover; when it C requires 2, place the second tablet at the bottom of the appliance. Remove detergent residues from the edges of the compartment and close the cover until it clicks. D A B Washing options Delayed start It is possible to delay the start time of the cycle by 2, 4 or 6 hours. Press the DELAYED START button: every time the button is pressed, a beep is emitted and the selected delayed start indicator light illuminates. Be filled: • when the green float* cannot be seen by simply looking at the cap of the salt dispenser; • when the LOW SALT* indicator light on the panel flashes; • if your machine is not equipped with an indicator light or a green float: approximately every 30 wash cycles; 1. Remove the lower rack and unscrew the cap of the dispenser (in an anticlockwise direction).  If you are using multi-functional tablets (2-in-1, 3-in-1, 4-in-1, etc. ) and you wish to further improve the drying performance of the appliance, fill the dispenser and set the dosage adjuster to 2. Loading the refined salt In order to obtain the best possible results from a wash cycle, make sure that the dispenser is never empty. Refined salt removes limescale from the water, thus avoiding the formation of deposits on crockery. The salt dispenser is located in the lower part of the dishwasher (see Description) and should The default setting of the water softening system is +. ) fill the salt dispenser and set the adjuster to -; if the hardness of the water is greater than 60°fH, set it to +. 20 Care and maintenance Shutting off the water and electricity supplies • Turn off the water tap after every wash cycle to avoid leaks. €¢ Remove the plug from the socket when cleaning the machine and when carrying out maintenance work. Cleaning the filters The filters remove food residue from the water used in the wash cycle: to obtain the best results from each wash, they should be cleaned. [. . . ] €¢ To avoid wasting detergent, use the product in appropriate quantities based on the manufacturer’s recommendations, the hardness of the water and the soil level and quantity of the crockery. Even if they are biodegradable, detergents contain substances that may alter the balance of nature. Disposal of old electrical appliances The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. [. . . ]