User manual WHIRLPOOL WRF989SDAE ENERGY GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WRF989SDAE. We hope that this WHIRLPOOL WRF989SDAE user guide will be useful to you.


WHIRLPOOL WRF989SDAE ENERGY GUIDE: Download the complete user guide (42 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL WRF989SDAE DIMENSION GUIDE (94 ko)
   WHIRLPOOL WRF989SDAE USE & CARE GUIDE (4105 ko)
   WHIRLPOOL WRF989SDAE WARRANTY INFORMATION (112 ko)

Manual abstract: user guide WHIRLPOOL WRF989SDAEENERGY GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] To ensure continued protection and sanitation, observe the following: DESCRIPTION Designed to be manually filled with ice from any remote ice-making source, these dispensers will dispense cubes (up to 1-1/4" in size), cubelets and hard-chipped or cracked ice. IMPORTANT: For dispensing compressed or extruded style ice, an Ice Diverter Kit must be installed on the dispensers (see ICE DIVERTER KIT (KNUGDIV) in INSTALLATION INSTRUCTIONS section of this manual. The Ice Diverter Kit is part of the KBT46 adapter. ·ALWAYS: disconnect power to the dispenser before servicing or cleaning. ·NEVER: place hands inside of hopper or gate area without disconnecting power to the dispenser. dispenser is energized! ·Agitator rotation occurs automatically when ·ALWAYS: be sure the removable lid is properly installed to prevent unauthorized access to the hopper interior and possible contamination of the ice. [. . . ] clean of ice cubes. ·ALWAYS: be sure the upper and lower front ·ALWAYS: keep area around the dispenser ·CAUTION: Dispenser cannot be used with crushed or flaked ice. Use of bagged ice, which has frozen into large chunks, can void warranty. Use of large chunks of ice which "jam up" inside the hopper will cause failure of the agitator motor and damage to the hopper. If bagged ice is used, it must be carefully and completely broken into small, cube-sized pieces before filling into the dispenser hopper. May 2002 Page 3 ID150, WRF989SDAE, ID250 INSTALLATION 1. Allow vertical clearance above unit for the removal of the cover, and for pouring ice into the hopper. Sufficient fittings are included with the unit to install in most cases. In order to comply with National Sanitation Foundation (NSF) requirements, this unit must be either elevated above the counter top sufficiently to provide space for cleaning under the unit or sealed to the counter top. IMPORTANT: It is the responsibility of the Installer to ensure that the water supply to the dispensing equipment is provided with protection against backflow by an air gap as defined in ANSI/ASME A112. 1. 2-1979; or an approved vacuum breaker or other such method as proved effective by test. Water pipe connections and fixtures directly connected to a potable water supply shall be sized, installed, and maintained according to Federal, State, and Local Codes. Drip Tray Assembly DRIP TRAY DRAIN ASSEMBLY (see illustration below): Route the drain tube to an open drain with the end of the tube above the "flood" level of the drain. Use the tubing, fittings, clamps, and insulation provided with the Dispenser to assemble the drain. Do not use metal scrapers, sharp objects or abrasives on the ice storage hopper, top cover and the agitator disk, as damage may result. Do not use solvents or other cleaning agents, as they may attack the plastic material. Soap solution - Use a mixture of mild detergent and warm (100 degrees F) potable water. May 2002 Page 10 ID150, WRF989SDAE, ID250 CLEANING AND SANITIZING MONTHLY & INITIAL START UP: Sanitize the Ice Storage System. Do not use metal scrapers, sharp objects or abrasives on the ice storage hopper, top cover and the agitator disk, as damage may result. Do not use solvents or other cleaning agents, as they may attack the plastic material. Soap solution - Use a mixture of mild detergent and warm (100 degrees F) potable water. Mix a solution of 1 ounce of household bleach to 2 gallons of potable water, or: mix a solution of any locally approved sanitizer, following the directions for mixing and applying that sanitizer. CAUTION: When pouring liquid into the hopper, do not exceed the rate of 1/2 gallon per minute. Using a long handle nylon bristle brush, clean the interior of the hopper, and top cover with soap solution. Clean the agitator assembly with soap solution using a nylon brush or a sponge. [. . . ] Clean the agitator assembly with soap solution using a nylon brush or a sponge. Thoroughly rinse the hopper, top cover and agitator with clean potable water. With a nylon bristle brush or sponge, clean the inside of the ice chute, gasket and cover with soap solution and rinse thoroughly to remove all traces of detergent. Using a mechanical spray bottle filled with sanitizing solution, spray the entire interior and agitator assembly. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WRF989SDAE




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WRF989SDAE will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.