User manual WHIRLPOOL W8RXNGMBB WARRANTY INFORMATION

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL W8RXNGMBB. We hope that this WHIRLPOOL W8RXNGMBB user guide will be useful to you.


WHIRLPOOL W8RXNGMBB WARRANTY INFORMATION: Download the complete user guide (101 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL W8RXNGMBB ENERGY GUIDE (1650 ko)
   WHIRLPOOL W8RXNGMBB DIMENSION GUIDE (73 ko)
   WHIRLPOOL W8RXNGMBB USE & CARE GUIDE (1299 ko)

Manual abstract: user guide WHIRLPOOL W8RXNGMBBWARRANTY INFORMATION

Detailed instructions for use are in the User's Guide.

[. . . ] Remove the door by tilting forward and lifting off the bottom hinge pin. Start in the middle and pull outward, moving toward the edge (see Figure 1). Remove the three screws located Figure 1 on the back of the handle (see Figure 2). [. . . ] Remove the three screws located Figure 1 on the back of the handle (see Figure 2). (This handle will be replaced with the modified handle included in the full overlay kit. ) e. Attach the modified handle to the lower handle using the three screws removed in Step Figure 2 1 C. Slide the existing door panel out of the door frame. NEW HANDLE OLD HANDLE 2. PREPARE THE NEW OVERLAY PANEL Refer to the Full Overlay Panel Preparation instruction sheet. The full overlay door panel must not weigh more than 20 lbs. Use two #6 screws (P/N 42122) to attach top pivot bracket (P/N 12029) to the wood door panel (see Figure 3). TOP PIVOT PLATE TYPICAL WOOD PANEL #6 X 5/8" FLAT HEAD SCREW TWO REQUIRED 8MM PLUG INSERT TWO REQUIRED Figure 3 b. If required, attach optional cabinet handle hardware to the wood door panel at this time. Place and tape the existing door panel on the back of the wood panel (see Figure 4) and drill holes through both panels according to the diagram (see Figure 5). Check to see that light switch actuator bracket is contacting the light switch properly. Full Overlay Panel Preparation for EchelonTM Models 2075, 2015 and CLR 2060 The full overlay door panel must not weigh more than 20 lbs. Be sure to note which model the door will be used on. PIVOT PLATE RELIEF SEE FIGURE 2 29-7/8" MODEL 2075: 23-3/4" MODEL 2015 and CLR 2060: 14-3/4" Figure 1 Rear View of Wood Panel For Right Hand Hinge Shown. Create a relief (Figure 2) for pivot plate by cutting notch in top corner and coinciding back corner of panel. Refer to the following figures for exact specifications. 3/4" 13/16" 1/8" 1/8" U-LINE034 Figure 2 Relief Notch for Pivot Plate Printed in U. S. A. (#16 DRILL) X 11/16" DEEP 3/8" 13/32" 3/8" 13/16" DOOR BOTTOM: 5/16" Dia. X 1/4" DEEP CHAMFER 1/32" X 45° Figure 3A Top View of Door 13/32" 1/8" 5/16" Dia. X 1/2" DEEP Figure 3C Bottom View of Door 1/8" 13/16" 1-17/32" 1/8" R1/32" 7/16" 13/16" R1/8" 3/4" Figure 3B Back View of Door Figure 3D Side View of Door 2A. Width: 13/16" Depth: 1/8" 4. Drill hole for upper door hinge (top of panel) (Figure 3A). [. . . ] X 1/4" DEEP CHAMFER 1/32" X 45° Figure 3A Top View of Door 13/32" 1/8" 5/16" Dia. X 1/2" DEEP Figure 3C Bottom View of Door 1/8" 13/16" 1-17/32" 1/8" R1/32" 7/16" 13/16" R1/8" 3/4" Figure 3B Back View of Door Figure 3D Side View of Door 2A. Width: 13/16" Depth: 1/8" 4. Drill hole for upper door hinge (top of panel) (Figure 3A). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL W8RXNGMBB




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL W8RXNGMBB will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.