User manual WESTERN DIGITAL WD10000H1NC

[. . . ] Single and Dual-drive Network Storage Systems ® TM My Book World Edition User Manual Important Safety Instructions 1. Do not block the slots and openings on the back or bottom side of the chassis; to ensure proper ventilation and reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. Operate this product only from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company. [. . . ] You can also manually specify the IP address of the NTP servers to which you want to synchronize. To configure system general setup settings: 1. Assign a device name for this storage device in the Device Name field. The device name can contain up to 15 characters, including alphabetic, numeric, space, and most special characters. Enter the brief description for this storage device in the Device Description field. The maximum length of the description must not be more than 256 alphanumeric characters. In web access protocol, select either of the following web access protocols: · · Hypertext Transfer Protocol (HTTP) is a communications protocol for the transfer of information on the intranet and the World Wide Web. Hypertext Transfer Protocol over Secure Socket Layer or HTTPS is a URL scheme used to indicate a secure HTTP connection. It is syntactically identical to the http:// scheme normally used for accessing resources using HTTP. HTTPS provides a more secure means of configuring your device, but may affect the responsiveness of the user interface. 4. To set the date and time manually, deselect Enable next to NTP Service. Click Submit. NETWORK STORAGE MANAGER - 73 MY BOOK WORLD EDITION USER MANUAL Alerts Setup Using the Alerts Setup submenu, you can configure e-mails or popup messages that provide alerts for system conditions, over temperature; hard drive, volume, network, and USB status; and user and group events. These alerts help the system administrator(s) manage and detect events or errors. Note: E-mail alerts may not work with some ISPs using strong spam filtering. For further information, go to support. wdc. com and search the knowledge base for answer ID 2570. To set up automatic e-mail notifications: 1. Enter the name of the SMTP server or an IP address to be used for sending email in the SMTP Server field (check with your ISP provider for the SMTP server name). Enter the port number to be used when connected for SMTP sending in the SMTP Port field. Click Enable next to SMTP Authentication if required, then enter the user name and password. Enter the e-mail address where you want to send an e-mail message when an event occurs in the Email Recipients field. Click Send Test Mail to send a test alert and confirm your settings are correct. NETWORK STORAGE MANAGER - 74 MY BOOK WORLD EDITION USER MANUAL 7. Click Submit. To configure alerts to send pop-up messages when an event occurs: Note: Pop-up notification only works with Windows XP. For a list of events, see "System Events" on page 136. Up to five computer names can be added to the alert list. Note: To find the name of your computer, click Start and right-click Computer or My Computer, click Properties, and then click the Computer Name tab (Windows XP). 3. Click Send Test Pop-up to send a test alert and confirm that the settings are correct. Note: Make sure the Messenger Service is activated on the computers to which you want to send the pop-up message when an event occurs. To enable Messenger Service, go to Start > Control Panel > Administrative Tools > Services > Messenger. [. . . ] WD shall have no liability for lost data regardless of the cause, recovery of lost data, or data contained in any Product placed in its possession. Limited Warranty WD warrants that the Product, in the course of its normal use, will be free from defects in material and workmanship for a period of three (3) years, unless otherwise required by law, and will conform to WD's specification therefor. This limited warranty period shall commence on the purchase date appearing on your purchase receipt. WD shall have no liability for any Product returned if WD determines that the Product was stolen from WD or that the asserted defect a) is not present, b) cannot reasonably be rectified because of damage occurring before WD receives the Product, or c) is attributable to misuse, improper installation, alteration (including removing or obliterating labels and opening or removing external enclosures, including the mounting frame, unless the product is on the list of limited userserviceable products and the specific alteration is within the scope of the applicable instructions, as found at support. wdc. com), accident or mishandling while in the possession of someone other than WD. [. . . ]