User manual WESTERN DIGITAL EIDE HARD DRIVE INSTALLATION GUIDE

[. . . ] Western Digital EIDE Hard Drive Installation Guide Western Digital EIDE Hard Drive Installation Guide Information furnished by Western Digital is believed to be accurate and reliable. However, no responsibility is assumed by Western Digital for its use; nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Western Digital. Western Digital reserves the right to change specifications at any time without notice. [. . . ] If Data Lifeguard Tools has detected Windows XP SP1 or Windows 2000 SP3, Dynamic Drive Overlay (DDO) will automatically be selected and installed in the next step. DDO is a device driver that overcomes your system's BIOS limitations to achieve full drive capacity. After Data Lifeguard Tools displays the steps completed, click Done to exit the software and begin using your new drive. DATA LIFEGUARD TOOLS V11. 0 - 18 WESTERN DIGITAL EIDE HARD DRIVE INSTALLATION GUIDE Drive-to-Drive Copy Utility The Drive-to-Drive Copy utility enables you to copy files from one drive to another. This feature is useful if you wish to replace your existing bootable hard drive with a newer, faster hard drive. You can click on Browse to easily access the folder or files on both hard drives. Note: Existing files on the destination hard drive will be overwritten if there are files on the source drive with the same name. When you have selected the folder for each path, click Start to begin drive copy. The progress bar for the current file being copied and the overall progress is displayed. 4. When copy operation is complete, click OK to display the results summary. Remove the CD and restart the computer to use your new Western Digital hard drive. DATA LIFEGUARD TOOLS V11. 0 - 19 WESTERN DIGITAL EIDE HARD DRIVE INSTALLATION GUIDE Hard Drive Information This feature allows you to view the drive model, serial number, capacity, UDMA mode, and other details about the selected hard drive. In the next window, you are given options to either select View Hard Drive Information or View Jumper Settings. a) View Hard Drive Information - Once your drive is detected, click on the tabs for either Partition Table or IDE Information to display data regarding the type of drive format, LBA support, DMA support, firmware revision, etc. b) View Jumper Settings - To view the jumper settings for your drive, select the drive model number and configuration, then click View Jumper Settings. The selected jumper setting diagram will display in your default Web browser. DATA LIFEGUARD TOOLS V11. 0 - 20 WESTERN DIGITAL EIDE HARD DRIVE INSTALLATION GUIDE Install the Hard Drive in a Macintosh System You can install two IDE/ATA hard drives on the same cable with the Master/Slave jumper configuration in the following Macintosh systems: !! Power Mac® G4 and higher Power Mac G3 (blue and white colored, limited to certain configurations) Power Mac G3 All-in-One (limited to certain configurations) A Power Mac with a U-shaped mounting bracket installed in the rear drive bay is capable of supporting dual IDE/ATA drives, allowing two drives to be installed in that bay. For more information on Master/Slave support on Power Macs G3 or G4, refer to Apple support article 24342 at www. apple. com. IMPORTANT: For detailed setup and installation instructions specific to your Macintosh system, refer to your original Apple Setup Guide or go to www. apple. com/support. You can install the hard drive according to one of the following system configurations: a) If your system does not support the Master/Slave configuration, you will be limited to installing one IDE/ATA device per channel for a maximum of two IDE/ATA devices. b) To install a drive greater than 137 GB, you must install a Macintosh-compatible Ultra ATA/100 controller card. Make sure that the Ultra ATA drivers have been properly installed prior to connecting the hard drive. c) To install a hard drive less than 137 GB as an additional hard drive in a Power Mac, follow the steps below. Install the Hard Drive Less than 137 GB (Additional drive) 1. Cable Select is the default jumper setting of your Western Digital hard drive, so you must change the configuration to Slave (see page 4 for a diagram of the jumper block). The drive that came with the Macintosh is already designated as Master (Master ID=0, Slave ID=1). [. . . ] No warranty service is provided unless the Product is returned to an authorized return center in the region (Americas, Europe-Middle East-Africa, or Asia Pacific) where the Product was first shipped by WD. IMPORTANT: If your Product was originally purchased as a component integrated within a system by a system manufacturer, no limited warranty is provided by WD. Contact the place of purchase or the system manufacturer directly for warranty service. Return Material Authorization No Product may be returned directly to WD without first contacting WD for a Return Material Authorization (RMA) number. An RMA number may be obtained from our online support Web site at support. wdc. com. [. . . ]