User manual WELLTECH SIP PHONE LP101

[. . . ] SIP-Phone User Manual Chapter 1 Overview of the SIP-Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. Front View and Keypad function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. Back View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please remember to configure these commands before start to work with SIP-Phone. Note: After change any settings, please remember to reboot (in Reboot System) SIP-Phone so that changes can take effect. 25 SIP SIP-Phone Administration Guide 1. Network Interface Please refer to chapter 4. 7 [ifaddr] command. - IP Address: Set IP Address of SIP-Phone Subnet Mask: Set the Subnet Mask of SIP-Phone Default routing gateway: Set Default routing gateway of SIP-Phone Get IP Mode: User has to set SIP-Phone to use which network mode. DHCP: When DHCP function enables, SIP-Phone will automatically search DHCP server after reboot. PPPoE: If SIP-Phone is working with PPPoE connection, user have to set related parameters in "PPPoE Configure "page. Note: If User set "Get IP mode" as DHCP or PPPoE, IP address, Subnet Mask, and Default routing gateway will become 0. 0. 0. 0 and not allow to be configured. 26 SIP SIP-Phone Administration Guide 27 SIP SIP-Phone Administration Guide - - - - SNTP: Enable / Disable the Simple Network Time Protocol function SNTP Server Address: Set SNTP Server Address When SNTP server is available, enable SIP-Phone SNTP function to point to SNTP server IP address so that SIP-Phone can get correct current time. GMT: Set time zone for SNTP Server time User can set different time zone according to the location of SIP-Phone. For example, in Taiwan the time zone should be set as 8, which means GMT+8. UPnP: Enable it if IP sharing or NAT device supports UPnP function so that no need to configure IP sharing or SIP-Phone when SIP-Phone is behind NAT device. IP Sharing Server Address: Set Public IP Address of IP Sharing router for SIP-Phone to work behind IP sharing. Once SIP-Phone can connect with DNS server, user can specify URL address instead of IP address for Proxy and phone book IP address. Secondary DNS Server: Set Secondary Domain Name Server IP address. 28 SIP SIP-Phone Administration Guide 2. SIP Information Please refer to chapter 4. 13 [SIP] command - Run Mode: Select SIP-Phone to work under Peer-to-Peer mode or Proxy mode. Proxy IP Address: Set Proxy IP Address or URL address (Domain Name Server must be configured. Outbound Proxy: Set IP Address or URL address (Domain Name Server must be configured. Proxy port: Set Proxy port for SIP-Phone to send message, default value is 5060, if there is no special request of Proxy server, please don't change this value. If user enabled this function, SIP-Phone will search dialed number in phone book to see if there is any matched table before send to Proxy server, and if there is a matched data in phone book, SIP-Phone will make call to related IP address. If user ID contains alphabets, user can set it as prefix 29 - SIP SIP-Phone Administration Guide - - string here. For example, if Account Name is 123, SIP-Phone will sent out messages as Account Name @"IP address of Proxy", if user set prefix as abc, SIP-Phone will set out as abc123@"IP address of Proxy". Line Number: identify one number for the SIP-Phone to register to the Proxy. If password is no need, please set user name the same as line number or SIP-Phone won't register successfully. SIP-Phone will keep re-registering to proxy server before expire timed out 30 SIP SIP-Phone Administration Guide 3. [. . . ] ­clean: clean up password restored before, and user can login :"root/administrator", password: "press enter". User who requests authorization to execute all configuration commands needs to login with "root". If a user login with "administrator", two commands are not functional: 1. passwd ­clean: clean up password restored before, and user can login :"root/administrator", password: "press enter". 54 SIP SIP-Phone Administration Guide Chapter 5 Upgrading Software on the SIP-Phone SIP-Phone supports three methods to upgrade the new version. [. . . ]