User manual WELLTECH FXSO GATEWAY H.323 3702A

[. . . ] FXSO GATEWAY User Manual (3701A/02A) Notice © Copyright 2002 Welltech Computer Co. , Ltd. All intellectual property rights in this publication are owned by Welltech Computer Co. , Ltd. and are protected by Republic of China copyright laws, other applicable copyright laws and international treaty provisions. No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by Welltech Computer Co. , Ltd. [. . . ] Ltd. 68 FXSO H. 323 Gateway User Manual Document Ver. : 2. 2 Release Mar. , 2004 3. 20 Flash Clean Users could make all the configurations back to the default setting by this button. The password of the account and the networking configuration couldn't be back to the default setting by this command. Ltd. 69 FXSO H. 323 Gateway User Manual Document Ver. : 2. 2 Release Mar. , 2004 Figure 3. 31: Flash Clean 3. 21 Commit This web page could save the configurations if users change some configurations. Ltd. 70 FXSO H. 323 Gateway User Manual Document Ver. : 2. 2 Release Mar. , 2004 Figure 3. 32: Commit 3. 22 Reboot System This web page will restart the whole system. This is the necessary step for the changing the configurations and makes it executed. Ltd. 71 FXSO H. 323 Gateway User Manual Document Ver. : 2. 2 Release Mar. , 2004 Figure 3. 33: Reboot System 4. Ltd. 72 FXSO H. 323 Gateway User Manual Document Ver. : 2. 2 Release Mar. , 2004 4. 1 Hyper Terminal Setting A terminal emulator is needed when using RS-232 port to configure Gateway. Here, we use Microsoft HyperTerminal to depict how to set up terminal emulator: 1 Execute the Hyper Terminal program, and then the following windows will pop-up on the screen. (START ­ Program files ­ Accessories ­ Communication ­ Hyper Terminal) Figure 4. 1: Hyper Terminal 2 Define a name such as `wg37' for this new connection. Copyright (c) 2002 Welltech Computer Co. Ltd. 73 FXSO H. 323 Gateway User Manual Document Ver. : 2. 2 Release Mar. , 2004 Figure 4. 2: Edit the name of the connection 3 After pressing OK button, the next window appears, and then chooses COM1/2 Port, which you are going to use. Figure 4. 3: Pick up the right interface to use Copyright (c) 2002 Welltech Computer Co. Ltd. 74 FXSO H. 323 Gateway User Manual Document Ver. : 2. 2 Release Mar. , 2004 4 Configure the COM Port Properties as following: Bits per second: 9600 Flow control: None Figure 4. 4: Configure the right Bps and control 5 Press `OK' button, and then start to configure Gateway. Copyright (c) 2002 Welltech Computer Co. Ltd. 75 FXSO H. 323 Gateway User Manual Document Ver. : 2. 2 Release Mar. , 2004 4. 2 Command List 4. 2. 1 [help] Type help or man or ?usr/config$ help help quit debug reboot flash commit ifaddr time ping sysconf h323 line route prefix pbook voice support phone tone fxopwd record tos ddns pt rom passwd help/man/?[command] quit/exit/close show debug message reboot local machine clean configuration from flash rom commit flash rom data Internet address manipulation show current time test that a remote host is reachable System information manipulation H. 323 information manipulation Line information manipulation Routing information manipulation Prefix drop/insert information manipulation Phone book information manipulation Voice information manipulation Special Voice function support manipulation Setup of call progress tones and ringing Setup of disconnect tone Setup of FXO password Record voice for greeting and ask pin code IP Packet ToS (Type of Service) values Dynamic DNS update manipulation DSP payload type configuration and information ROM file update Password setting information and configuration Copyright (c) 2002 Welltech Computer Co. Ltd. 76 FXSO H. 323 Gateway User Manual Document Ver. : 2. 2 Release Mar. , 2004 usage: help [command] 4. 2. 2 [quit] Type quit will quit the Gateway configuration mode and turn back to login prompt (in console mode) or disconnect (in TELNET mode). login: Note: It is recommended that type the "quit" command before you leave the console. If so, Gateway will ask password again when next user connects to console port. 4. 2. 3 [debug] Open debug message will show up specific information while Gateway is in operation. After executing the debug command, it should execute command debug -open as well. usr/config$ debug -add h323 vp h323vp usr/config$ debug -open In this example, user open debug flags including h323, vp, h323vp. -- h323 : h323 related information -- vp : voice related information -delete -open -close Remove specified debug flag. Stop showing debug messages. 4. 2. 4 [reboot] After commit command, type reboot to reload Gateway in new configuration. The procedure is as below: usr/config$ reboot 77 Copyright (c) 2002 Welltech Computer Co. [. . . ] (Please make sure that you are already finish the steps 2 ~ 7) r (Press "Enter" button after you key in "R") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (You could hang up the call from PSTN if you get this message) Frequency 1 : 473 Frequency 2 (2623) is more than 1000, please ignore it. [. . . ]