User manual VTECH VT9111

[. . . ] INTRODUCTION USER'S MANUAL VTECH V T 9 1 1 1 / V T 9 1 1 5 900MHz ANALOG CORDLESS TELEPHONE Parts Check List: 1. Wall mounting bracket HANDSET BASE UNIT IMPORTANT BEFORE USING YOUR NEW PHONE, WE STRONGLY RECOMMEND YOU READ THIS MANUAL THOROUGHLY. TELEPHONE LINE CORD AC ADAPTER VTECH COMMUNICATIONS LTD. Copyright 1998 for VTECH COMMUNICATIONS LTD. ISSUE 0 91-5017-32-00 BATTERY PACK 1 WALL MOUNT BRACKET IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool). [. . . ] Answering Calls When an incoming call is ringing, the IN USE LED on the base and PHONE LED on the handset will flash. To make sure your phone rings when the handset is away from the base, please keep the base antenna in the upright position. To answer a call when the handset is in the base, just pick up the handset. To answer a call when the handset is away from the base, just press any key on the handset (except OFF). This is very useful in a dark environment; you do not have to fumble around looking for the PHONE key to answer the call. OPERATING INSTRUCTIONS Disconnecting To end a call, either place the handset back in the base, or press OFF on the handset. Changing Channels If you notice interference when using your handset, press CHAN to switch to a clear channel. 9 IN USE LED VOLUME SWITCH PHONE KEY OFF KEY CHAN KEY CHARGING LED IN USE LED POWER LED TONE/ KEY PROG KEY MEM KEY REDIAL KEY PAGE KEY 8 OPERATING INSTRUCTIONS To Change or Replace a Speed Dial Number To change or replace a stored number in speed dial memory simply enter the new number and store it in the memory location you wish to change. For example, to change the number stored in memory position 7 to 555-1111, you would press PROG, 7, 555-1111, MEM. Storing Pauses in Memory To insert a pause in a phone number, press and hold the number before the position where the pause is to be inserted. For longer pauses, press and hold the key until it beeps three or four times. If your phone is connected to a PBX you can store the PBX access number and a pause before the phone number. For example, to store 9-PAUSE-555-1234 in memory location 8 do the following: 10 1. Press MEM Using REDIAL To REDIAL the last number you called, press PHONE then press REDIAL. Storing a Redial Number into Speed Dial To store the last number you dialed as a regular Speed Dial number, press PROG, a number key (0-9), REDIAL, MEM. The Page Feature From the base unit, press PAGE to signal the person at the handset. This feature is also useful if you have misplaced the handset. IN CASE OF DIFFICULTY If you have difficulty operating your phone, the suggestions below should solve the problem. If you still have difficulty after trying these suggestions, In the US call: VTECH Communications at 1-800-595-9511. * Make sure the telephone line cord is plugged firmly into the base unit and the telephone wall jack. If the IN USE indicators do not light when you press PHONE, you must charge the batteries. * If you recently installed a new battery pack, make sure it is installed correctly. * If you still don't hear a dial tone, disconnect the base unit from the telephone jack and connect a different phone. If there is no dial tone on that phone either, the problem is in your wiring or local service. [. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be 14 determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected. [. . . ]