User manual VTECH VT1932

[. . . ] Handset Base Unit AC Power Adaptor Battery Pack Wall Mounting Bracket Telephone Line Cord Belt Clip To purchase replacement battery packs, call VTECH Communications at 1-800595-9511. In Canada, call VTECH Electronics at 1-800-267-7377. WALL MOUNTING BRACKET HANDSET BASE UNIT BATTERY PACK AC POWER ADAPTOR TELEPHONE LINE CORD BELT CLIP 1 FCC AND IC REGULATIONS This equipment complies with Parts 15 and 68 of the Federal Communications Commission (FCC) rules for the United States. It also complies with regulations RSS210 and CS-03 of Industry and Science Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. [. . . ] Press REDIAL/ 17 DIRECTORY EDITING A DIRECTORY ENTRY · Press OK . · Press or to scroll to the desired name; or, search by entering the first letter of the name, and then or if necessary. When the number is correct, press OK. BASE UNIT OPERATION ERASING A DIRECTORY ENTRY · Press OK . · Press or to scroll to the desired name; or, search by entering the first letter of the name, and then press or if necessary. · Press OK . CHARGING: illuminates when the Handset is cradled. SPARE BATTERY: illuminates when a battery Pack is charging in the Base Unit charger. SPEAKERPHONE TIPS If you use the Speakerphone in an environment that's not very quiet, your caller's voice may fade in and out. Should this occur, try reducing the room noise (loud conversation, a TV or radio playing, for example). Press MUTE again when it's your turn to speak. 18 BASE UNIT OPERATION SPEED DIALING · Press SPEAKERPHONE. STORING A PAUSE IN A DIALING SEQUENCE To insert a pause while programming a speed dial number, press REDIAL/ PAUSE at the appropriate point in the number sequence. INTERCOM You can Intercom the Handset from the Base Unit (or vice versa). On the Handset, press INT. COM to respond to the page, or press OFF to terminate the page. When the Handset initiates the page, the Base Unit will ring twice, and enter Intercom mode. CALL WAITING CALLER ID (CID) In the OFF (on-hook) mode, the Base Unit will display CALLER ID data as the call comes in. In the SPEAKERPHONE (off-hook) mode, the Base Unit will display CALL WAITING CALLER ID. · Press PROG. The Base will display : ENTER 0 TO 9 · Enter desired Location (0-9). The Base will display: ENTER NAME · Use the Base dial pad to enter the letters (16 characters maximum). The following table lists the characters found on each key: KEY CHARACTER 11 2 A>B>C>2 3 D>E>F>3 (etc. ) For the complete table, see: DIRECTORY - TO STORE A NAME AND NUMBER To enter 2 characters located on the same key, or, to add a space, use the VOLUME key. For example, to enter the name 'DEAN': · Press 3 · Press VOLUME · Press 3 twice · Press 2 · Press 6 twice · Press PROG when you finish entering the name. · Enter the telephone number you wish to store (32 digits maximum). 19 BASE UNIT OPERATION A NEW CALL light will flash on the Base Unit to alert you to new CID records. Once the new caller ID records have been reviewed on the Handset, the NEW CALL light will go out. NOTE: Caller ID and Call Waiting Caller ID are subscription services, available through most local phone service providers. [. . . ] 15 CALLER ID Reviewing the Call Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Erasing Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Speed Dialing from Caller ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 DIRECTORY To Store a Name And Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]