User manual VTECH VT 2932

[. . . ] Handset Base Unit Wall Mounting Bracket AC power Adaptor Telephone Line Cords (x2) Battery Pack Belt Clip To purchase replacement battery packs, call VTECH Communications at 1-800595-9511. In Canada, call VTECH Electronics at 1-800-267-7377. 10:00 AM SIMON JAMES WILD 654532 465929115 NEW 00 LINE1 LINE2 LINE 1 OFF LINE 2 1 2 GHI ABC 3 6 9 DEF 4 7 5 8 JKL MNO PQRS TUV WXYZ TONE 0 OPER PROG FLASH REDIAL/PAUSE HOLD CONF INTERCOM WALL MOUNTING BRACKET MIC HANDSET BASE UNIT AC POWER ADAPTOR TELEPHONE LINE CORDS SHORT LINE CORD BATTERY PACK BELT-CLIP 1 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. Slots and openings in the cabinet and the back or bottom are provided for ventilation, to protect it from overheating, these openings must not be blocked or covered. [. . . ] The following table lists the characters found on each key: KEY CHARACTER 11 2 A>B>C>2 3 D>E>F>3 etc. (For the complete table, see: DIRECTORY - TO STORE A NAME AND NUMBER). To enter 2 characters located on the same key, or, to add a space, use the key. VOLUME For example, to enter the name 'DEAN': · Press 3 · · · · · · · Press VOLUME Press 3 twice Press 2 Press 6 twice Press PROG when you finish entering the name. You will hear a confirmation beep, and the screen will go blank. 17 BASE UNIT OPERATION STORING A PAUSE IN A DIALING SEQUENCE To insert a pause while programming a speed dial number, press REDIAL/PAUSE at the appropriate point in the number sequence. Each pause is treated as a stored digit. INTERCOM You can Intercom the Handset from the Base Unit (or vice versa). On the Handset, press INT. COM to respond to the page, or press OFF to terminate the page. When the Handset initiates the page, the Base Unit will ring twice, and enter Intercom mode. Press INTERCOM/PAGE on the Base Unit to terminate Intercom mode. CALL WAITING CALLER ID (CID) In the OFF (on-hook) mode, the Base Unit will display CALLER ID data as the call comes in. In the SPEAKERPHONE (off-hook) mode, the Base Unit will display CALL WAITING CALLER ID. A NEW CALL light will flash on the Base Unit to alert you to new CID records. Once the new caller ID records have been reviewed on the Handset, the NEW CALL light will go out. NOTE: Caller ID and Call Waiting Caller ID are subscription services, available through most local phone service providers. You must subscribe to these services to benefit from the Caller ID features of this phone. Due to regional incompatibilities, Caller ID information may not be available for every call you receive. In addition, the calling party may intentionally block their name and phone number from being sent. DATA PORT Your VT2931 has a Data Port on the left-hand edge of the Base Unit. This port provides an easy way to connect your fax machine, laptop computer, modem, or other telephone device for direct acces to LINE2. The Data Port only provides access to Line 2, so you must have an active line connected to the LINE2 input on the back of the VT2931. Connect an RJ-11(2-element) phone cord from the Data Port to you fax, laptop, etc. DATA PORT NOTE: While the Data Port is in use, accidental use of Line 2 by a parallel phone, the VT2931 Handset, or a Call Waiting ID alert may in inerrupt the data transmission. 18 ADDITONAL OPERATIONS POWER BACKUP When a spare battery pack (optional) is installed in the Base Unit, your VTech cordless telephone uses this battery to provide operational backup during a power failure. If you have a fully charged battery pack in the Base Unit charger, you will be able to place and receive calls from the Handset for up to 5 hours. Note: During power backup mode, the Base Unit functions are not operable, In addition, Caller ID information may not be reliable. REPLACING A DRAINED HANDSET BATTERY The spare battery pack can also be used to replace a drained Handset battery, to ensure uninterrupted use. Be sure to put the drained battery pack in the Base Unit charger for recharging. The Base Unit battery compartment charges at a slower rate than a battery pack charging in the Handset. [. . . ] The general rule is that the REN value should not exceed 5. 0 total; however, contact your local telephone company for the specific number in your area. IC (Industry Canada) This telephone is registered for use in Canada. Notice: The REN assigned to this device denotes the number of devices you may connect to the telephone loop, which is used by the device to prevent overloading, The termination on a loop may consist of any combination of devices subjected only to the requirement that the sum of the REN does not exceed five (5. 0) Notice: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. [. . . ]